-- -- /****************************************************************/ -- /* (C) COPYRIGHT HEWLETT-PACKARD COMPANY 1996. ALL RIGHTS */ -- /* RESERVED. NO PART OF THIS DOCUMENT MAY BE PHOTOCOPIED, */ -- /* REPRODUCED OR TRANSLATED WITHOUT THE PRIOR WRITTEN CONSENT */ -- /* OF HEWLETT-PACKARD COMPANY. */ -- /****************************************************************/ -- -- -- This MIB file is the Master MIB file for the JetDirect SNMP implementation. -- It includes all objects defined for both internal cards and external boxes. -- -- This MIB successfully compiles with mosy 7.1. (as of 7/25/95) -- -- Last Updated: April 24, 1998 -- -- HP OBJECT IDENTIFIER ::= { iso org(3) dod(6) internet(1) private(4) enterprises(1) 11 } JETDIRECT3-MIB DEFINITIONS ::= BEGIN -- TAddress ::= OCTET STRING -- A TAddress is 6 octets long, the initial 4 octets -- containing the IP address in network byte order and the last 2 containing -- the UDP port in network byte order. --RowStatus ::= INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } IMPORTS private, enterprises, Counter, Gauge, TimeTicks, NetworkAddress, mgmt FROM RFC1155-SMI; -- textual conventions DisplayString ::= OCTET STRING -- This data type is used to model textual information taken -- from the NVT ASCII character set. By convention, objects -- with this syntax are declared as having -- -- SIZE (0..255) mib-2 OBJECT IDENTIFIER ::= { mgmt 1} interfaces OBJECT IDENTIFIER ::= { mib-2 2} hp OBJECT IDENTIFIER ::= { enterprises 11 } nm OBJECT IDENTIFIER ::= { hp 2 } system OBJECT IDENTIFIER ::= { nm 3 } interface OBJECT IDENTIFIER ::= { nm 4 } at OBJECT IDENTIFIER ::= { mib-2 3 } ip OBJECT IDENTIFIER ::= { mib-2 4 } icmp OBJECT IDENTIFIER ::= { mib-2 5 } tcp OBJECT IDENTIFIER ::= { mib-2 6 } udp OBJECT IDENTIFIER ::= { mib-2 7 } snmp OBJECT IDENTIFIER ::= { mib-2 11 } appletalk OBJECT IDENTIFIER ::= { mib-2 13 } net-peripheral OBJECT IDENTIFIER ::= { system 9 } net-printer OBJECT IDENTIFIER ::= { net-peripheral 1 } generalDeviceStatus OBJECT IDENTIFIER ::= { net-printer 1 } netPrinterType OBJECT IDENTIFIER ::= { net-printer 2 } ieee8023Mac OBJECT IDENTIFIER ::= { interface 1 } ieee8025Mac OBJECT IDENTIFIER ::= { interface 2 } npCard OBJECT IDENTIFIER ::= { interface 3 } npSys OBJECT IDENTIFIER ::= { npCard 1 } npConns OBJECT IDENTIFIER ::= { npCard 4 } npCfg OBJECT IDENTIFIER ::= { npCard 5 } npTcp OBJECT IDENTIFIER ::= { npCard 6 } npCtl OBJECT IDENTIFIER ::= { npCard 7 } npNpi OBJECT IDENTIFIER ::= { npCard 8 } npElt OBJECT IDENTIFIER ::= { npCard 9 } npIpx OBJECT IDENTIFIER ::= { npCard 10 } npDm OBJECT IDENTIFIER ::= { npCard 11 } llcconstategroup OBJECT IDENTIFIER ::= { npCard 12 } npPort OBJECT IDENTIFIER ::= { npCard 13 } npXip OBJECT IDENTIFIER ::= { npCard 14 } npCRC OBJECT IDENTIFIER ::= { npCard 15 } npDhcp OBJECT IDENTIFIER ::= { npCard 16 } npScan OBJECT IDENTIFIER ::= { npCard 17 } npWeb OBJECT IDENTIFIER ::= { npCard 18 } trap OBJECT IDENTIFIER ::= { nm 13 } trapDest OBJECT IDENTIFIER ::= { trap 1 } -- added for download icf OBJECT IDENTIFIER ::= { nm 14 } snmpAccess OBJECT IDENTIFIER ::= { nm 15 } community OBJECT IDENTIFIER ::= { snmpAccess 1} -- Icf Common Objects hpicfAdmin OBJECT IDENTIFIER ::= { icf 10 } hpicfObjects OBJECT IDENTIFIER ::= { icf 11 } hpicfCommon OBJECT IDENTIFIER ::= { hpicfObjects 1 } hpicfChain OBJECT IDENTIFIER ::= { hpicfCommon 1 } hpicfDomains OBJECT IDENTIFIER ::= { hpicfAdmin 1 } hpicfLLCDomain OBJECT IDENTIFIER ::= { hpicfDomains 1 } hpicfNBPDomain OBJECT IDENTIFIER ::= { hpicfCommon 2 } hpicfDownload OBJECT IDENTIFIER ::= { hpicfCommon 3 } atport OBJECT IDENTIFIER ::= { appletalk 3 } status-prt-eng OBJECT IDENTIFIER ::= { print-engine 2 } -- PML objects added to accomodate the object total-ENGINE-PAGE-COUNT netPML OBJECT IDENTIFIER ::= { net-peripheral 4 } netPMLmgmt OBJECT IDENTIFIER ::= { netPML 2 } device OBJECT IDENTIFIER ::= { netPMLmgmt 1 } destination-subsystem OBJECT IDENTIFIER ::= { device 4 } print-engine OBJECT IDENTIFIER ::= { destination-subsystem 1 } -- status-prt-eng OBJECT IDENTIFIER ::= { print-engine 2 } -- toptools branch hpWebMgmt OBJECT IDENTIFIER ::= { nm 36 } hpHttpMgMod OBJECT IDENTIFIER ::= { hpWebMgmt 1 } hpHttpMgObjects OBJECT IDENTIFIER ::= { hpHttpMgMod 1 } hpHttpMgDefaults OBJECT IDENTIFIER ::= { hpHttpMgObjects 1 } -- object types -- The MIB-II Objects supported by JetDirect products -- the System group sysDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (256)) ACCESS read-only STATUS mandatory DESCRIPTION "A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters." ::= { system 1 } sysObjectID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. The value for this device is constructed by appending the peripheral attribute class npNpiPaeClass to the sysObjId base: .1.3.6.1.4.1.11.2.3.9. See description of npNpiPaeClass below." ::= { system 2 } sysUpTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The time (in hundredths of a second) since the network management portion of the system was last re-initialized." ::= { system 3 } sysContact OBJECT-TYPE SYNTAX DisplayString (SIZE (256)) ACCESS read-write STATUS mandatory DESCRIPTION "The textual identification of the contact person for this managed node, together with information on how to contact this person." ::= { system 4 } -- Note that this may be either a bootp, DHCP or JetAdmin (SNMP) -- assigned name sysName OBJECT-TYPE SYNTAX DisplayString (SIZE (256)) ACCESS read-write STATUS mandatory DESCRIPTION "An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name." ::= { system 5 } sysLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (64)) ACCESS read-write STATUS mandatory DESCRIPTION "The physical location of this node (e.g., `telephone closet, 3rd floor'). This string can be set using two different methods. The first is through the tftp config file for the TCP solution. The other is using SNMP over any of the protocols. This value is saved in NVRAM. Using SNMP to set this object will cause the tftp version to be overwritten. If this object is set using SNMP then the tftp version from the tftp config file will NOT cause an overwrite at boot time." ::= { system 6 } sysServices OBJECT-TYPE SYNTAX INTEGER (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum." ::= { system 7 } -- the Interfaces group ifNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of network interfaces (regardless of their current state) present on this system." ::= { interfaces 1 } ifTable OBJECT-TYPE SYNTAX SEQUENCE OF IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of interface entries. The number of entries is given by the value of ifNumber." ::= { interfaces 2 } ifEntry OBJECT-TYPE SYNTAX IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An interface entry containing objects at the subnetwork layer and below for a particular interface." INDEX { ifIndex } ::= { ifTable 1 } IfEntry ::= SEQUENCE { ifIndex INTEGER, ifDescr DisplayString, ifType INTEGER, ifMtu INTEGER, ifSpeed Gauge, ifPhysAddress OCTET STRING, ifAdminStatus INTEGER, ifOperStatus INTEGER, ifLastChange TimeTicks, ifInOctets Counter, ifInUcastPkts Counter, ifInNUcastPkts Counter, ifInDiscards Counter, ifInErrors Counter, ifInUnknownProtos Counter, ifOutOctets Counter, ifOutUcastPkts Counter, ifOutNUcastPkts Counter, ifOutDiscards Counter, ifOutErrors Counter, ifOutQLen Gauge, ifSpecific OBJECT IDENTIFIER } ifIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization." ::= { ifEntry 1 } ifDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (256)) ACCESS read-only STATUS mandatory DESCRIPTION "A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface." ::= { ifEntry 2 } ifType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack." ::= { ifEntry 3 } ifMtu OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface." ::= { ifEntry 4 } ifSpeed OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth." ::= { ifEntry 5 } ifPhysAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { ifEntry 6 } ifAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), testing(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The desired state of the interface. The testing(3) state indicates that no operational packets can be passed." ::= { ifEntry 7 } ifOperStatus OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed." ::= { ifEntry 8 } ifLastChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value." ::= { ifEntry 9 } ifInOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets received on the interface, including framing characters." ::= { ifEntry 10 } ifInUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of subnetwork-unicast packets delivered to a higher-layer protocol." ::= { ifEntry 11 } ifInNUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol." ::= { ifEntry 12 } ifInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space." ::= { ifEntry 13 } ifInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol." ::= { ifEntry 14 } ifInUnknownProtos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets received via the interface which were discarded because of an unknown or unsupported protocol." ::= { ifEntry 15 } ifOutOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters." ::= { ifEntry 16 } ifOutUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent." ::= { ifEntry 17 } ifOutNUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent." ::= { ifEntry 18 } ifOutDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space." ::= { ifEntry 19 } ifOutErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of outbound packets that could not be transmitted because of errors." ::= { ifEntry 20 } ifOutQLen OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The length of the output packet queue (in packets)." ::= { ifEntry 21 } ifSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value." ::= { ifEntry 22 } -- the Address Translation group -- Implementation of the Address Translation group is -- mandatory for all systems. Note however that this group -- is deprecated by MIB-II. That is, it is being included -- solely for compatibility with MIB-I nodes, and will most -- likely be excluded from MIB-III nodes. From MIB-II and -- onwards, each network protocol group contains its own -- address translation tables. -- The Address Translation group contains one table which is -- the union across all interfaces of the translation tables -- for converting a NetworkAddress (e.g., an IP address) into -- a subnetwork-specific address. For lack of a better term, -- this document refers to such a subnetwork-specific address -- as a `physical' address. -- Examples of such translation tables are: for broadcast -- media where ARP is in use, the translation table is -- equivalent to the ARP cache; or, on an X.25 network where -- non-algorithmic translation to X.121 addresses is -- required, the translation table contains the -- NetworkAddress to X.121 address equivalences. atTable OBJECT-TYPE SYNTAX SEQUENCE OF AtEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "The Address Translation tables contain the NetworkAddress to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries." ::= { at 1 } atEntry OBJECT-TYPE SYNTAX AtEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry contains one NetworkAddress to `physical' address equivalence." INDEX { atIfIndex, atNetAddress } ::= { atTable 1 } AtEntry ::= SEQUENCE { atIfIndex INTEGER, atPhysAddress OCTET STRING, atNetAddress IpAddress } atIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS deprecated DESCRIPTION "The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { atEntry 1 } atPhysAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS deprecated DESCRIPTION "The media-dependent `physical' address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object." ::= { atEntry 2 } atNetAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS deprecated DESCRIPTION "The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address." ::= { atEntry 3 } -- the IP group ipForwarding OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value." ::= { ip 1 } ipDefaultTTL OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol." ::= { ip 2 } ipInReceives OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of input datagrams received from interfaces, including those received in error." ::= { ip 3 } ipInHdrErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc." ::= { ip 4 } ipInAddrErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address." ::= { ip 5 } ipForwDatagrams OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful." ::= { ip 6 } ipInUnknownProtos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol." ::= { ip 7 } ipInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly." ::= { ip 8 } ipInDelivers OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of input datagrams successfully delivered to IP user-protocols (including ICMP)." ::= { ip 9 } ipOutRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams." ::= { ip 10 } ipOutDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion." ::= { ip 11 } ipOutNoRoutes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down." ::= { ip 12 } ipReasmTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity." ::= { ip 13 } ipReasmReqds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP fragments received which needed to be reassembled at this entity." ::= { ip 14 } ipReasmOKs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams successfully re- assembled." ::= { ip 15 } ipReasmFails OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received." ::= { ip 16 } ipFragOKs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams that have been successfully fragmented at this entity." ::= { ip 17 } ipFragFails OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set." ::= { ip 18 } ipFragCreates OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagram fragments that have been generated as a result of fragmentation at this entity." ::= { ip 19 } -- the IP address table ipAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IpAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of addressing information relevant to this entity's IP addresses." ::= { ip 20 } ipAddrEntry OBJECT-TYPE SYNTAX IpAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The addressing information for one of this entity's IP addresses." INDEX { ipAdEntAddr } ::= { ipAddrTable 1 } IpAddrEntry ::= SEQUENCE { ipAdEntAddr IpAddress, ipAdEntIfIndex INTEGER, ipAdEntNetMask IpAddress, ipAdEntBcastAddr INTEGER, ipAdEntReasmMaxSize INTEGER (0..65535) } ipAdEntAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address to which this entry's addressing information pertains." ::= { ipAddrEntry 1 } ipAdEntIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { ipAddrEntry 2 } ipAdEntNetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0." ::= { ipAddrEntry 3 } ipAdEntBcastAddr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface." ::= { ipAddrEntry 4 } ipAdEntReasmMaxSize OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface." ::= { ipAddrEntry 5 } -- the IP routing table ipRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpRouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's IP Routing table." ::= { ip 21 } ipRouteEntry OBJECT-TYPE SYNTAX IpRouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A route to a particular destination." INDEX { ipRouteDest } ::= { ipRouteTable 1 } IpRouteEntry ::= SEQUENCE { ipRouteDest IpAddress, ipRouteIfIndex INTEGER, ipRouteMetric1 INTEGER, ipRouteMetric2 INTEGER, ipRouteMetric3 INTEGER, ipRouteMetric4 INTEGER, ipRouteNextHop IpAddress, ipRouteType INTEGER, ipRouteProto INTEGER, ipRouteAge INTEGER, ipRouteMask IpAddress, ipRouteMetric5 INTEGER, ipRouteInfo OBJECT IDENTIFIER } ipRouteDest OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use." ::= { ipRouteEntry 1 } ipRouteIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { ipRouteEntry 2 } ipRouteMetric1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 3 } ipRouteMetric2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 4 } ipRouteMetric3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 5 } ipRouteMetric4 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 6 } ipRouteNextHop OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)" ::= { ipRouteEntry 7 } ipRouteType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object." ::= { ipRouteEntry 8 } ipRouteProto OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols." ::= { ipRouteEntry 9 } ipRouteAge OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned." ::= { ipRouteEntry 10 } ipRouteMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism." ::= { ipRouteEntry 11 } ipRouteMetric5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 12 } ipRouteInfo OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value." ::= { ipRouteEntry 13 } -- the IP Address Translation table ipNetToMediaTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The IP Address Translation table used for mapping from IP addresses to physical addresses." ::= { ip 22 } ipNetToMediaEntry OBJECT-TYPE SYNTAX IpNetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains one IpAddress to `physical' address equivalence." INDEX { ipNetToMediaIfIndex, ipNetToMediaNetAddress } ::= { ipNetToMediaTable 1 } IpNetToMediaEntry ::= SEQUENCE { ipNetToMediaIfIndex INTEGER, ipNetToMediaPhysAddress OCTET STRING, ipNetToMediaNetAddress IpAddress, ipNetToMediaType INTEGER } ipNetToMediaIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { ipNetToMediaEntry 1 } ipNetToMediaPhysAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The media-dependent `physical' address." ::= { ipNetToMediaEntry 2 } ipNetToMediaNetAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IpAddress corresponding to the media- dependent `physical' address." ::= { ipNetToMediaEntry 3 } ipNetToMediaType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object." ::= { ipNetToMediaEntry 4 } -- additional IP objects ipRoutingDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries." ::= { ip 23 } -- the ICMP group icmpInMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors." ::= { icmp 1 } icmpInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.)." ::= { icmp 2 } icmpInDestUnreachs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Destination Unreachable messages received." ::= { icmp 3 } icmpInTimeExcds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Time Exceeded messages received." ::= { icmp 4 } icmpInParmProbs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Parameter Problem messages received." ::= { icmp 5 } icmpInSrcQuenchs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Source Quench messages received." ::= { icmp 6 } icmpInRedirects OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Redirect messages received." ::= { icmp 7 } icmpInEchos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo (request) messages received." ::= { icmp 8 } icmpInEchoReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo Reply messages received." ::= { icmp 9 } icmpInTimestamps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp (request) messages received." ::= { icmp 10 } icmpInTimestampReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp Reply messages received." ::= { icmp 11 } icmpInAddrMasks OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Request messages received." ::= { icmp 12 } icmpInAddrMaskReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Reply messages received." ::= { icmp 13 } icmpOutMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors." ::= { icmp 14 } icmpOutErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value." ::= { icmp 15 } icmpOutDestUnreachs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Destination Unreachable messages sent." ::= { icmp 16 } icmpOutTimeExcds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Time Exceeded messages sent." ::= { icmp 17 } icmpOutParmProbs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Parameter Problem messages sent." ::= { icmp 18 } icmpOutSrcQuenchs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Source Quench messages sent." ::= { icmp 19 } icmpOutRedirects OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects." ::= { icmp 20 } icmpOutEchos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo (request) messages sent." ::= { icmp 21 } icmpOutEchoReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo Reply messages sent." ::= { icmp 22 } icmpOutTimestamps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp (request) messages sent." ::= { icmp 23 } icmpOutTimestampReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp Reply messages sent." ::= { icmp 24 } icmpOutAddrMasks OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Request messages sent." ::= { icmp 25 } icmpOutAddrMaskReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Reply messages sent." ::= { icmp 26 } -- the TCP group tcpRtoAlgorithm OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The algorithm used to determine the timeout value used for retransmitting unacknowledged octets." ::= { tcp 1 } tcpRtoMin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793." ::= { tcp 2 } tcpRtoMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793." ::= { tcp 3 } tcpMaxConn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1." ::= { tcp 4 } tcpActiveOpens OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state." ::= { tcp 5 } tcpPassiveOpens OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state." ::= { tcp 6 } tcpAttemptFails OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state." ::= { tcp 7 } tcpEstabResets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state." ::= { tcp 8 } tcpCurrEstab OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT." ::= { tcp 9 } tcpInSegs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments received, including those received in error. This count includes segments received on currently established connections." ::= { tcp 10 } tcpOutSegs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets." ::= { tcp 11 } tcpRetransSegs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets." ::= { tcp 12 } -- the TCP Connection table tcpConnTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpConnEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing TCP connection-specific information." ::= { tcp 13 } tcpConnEntry OBJECT-TYPE SYNTAX TcpConnEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state." INDEX { tcpConnLocalAddress, tcpConnLocalPort, tcpConnRemAddress, tcpConnRemPort } ::= { tcpConnTable 1 } TcpConnEntry ::= SEQUENCE { tcpConnState INTEGER, tcpConnLocalAddress IpAddress, tcpConnLocalPort INTEGER (0..65535), tcpConnRemAddress IpAddress, tcpConnRemPort INTEGER (0..65535) } tcpConnState OBJECT-TYPE SYNTAX INTEGER { closed(1), listen(2), synSent(3), synReceived(4), established(5), finWait1(6), finWait2(7), closeWait(8), lastAck(9), closing(10), timeWait(11), deleteTCB(12) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably)." ::= { tcpConnEntry 1 } tcpConnLocalAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used." ::= { tcpConnEntry 2 } tcpConnLocalPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The local port number for this TCP connection." ::= { tcpConnEntry 3 } tcpConnRemAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The remote IP address for this TCP connection." ::= { tcpConnEntry 4 } tcpConnRemPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The remote port number for this TCP connection." ::= { tcpConnEntry 5 } -- additional TCP objects tcpInErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments received in error (e.g., bad TCP checksums)." ::= { tcp 14 } tcpOutRsts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of TCP segments sent containing the RST flag." ::= { tcp 15 } -- the UDP group udpInDatagrams OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of UDP datagrams delivered to UDP users." ::= { udp 1 } udpNoPorts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of received UDP datagrams for which there was no application at the destination port." ::= { udp 2 } udpInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port." ::= { udp 3 } udpOutDatagrams OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of UDP datagrams sent from this entity." ::= { udp 4 } -- the UDP Listener table udpTable OBJECT-TYPE SYNTAX SEQUENCE OF UdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing UDP listener information." ::= { udp 5 } udpEntry OBJECT-TYPE SYNTAX UdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a particular current UDP listener." INDEX { udpLocalAddress, udpLocalPort } ::= { udpTable 1 } UdpEntry ::= SEQUENCE { udpLocalAddress IpAddress, udpLocalPort INTEGER (0..65535) } udpLocalAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used." ::= { udpEntry 1 } udpLocalPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The local port number for this UDP listener." ::= { udpEntry 2 } -- the SNMP group snmpInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Messages delivered to the SNMP entity from the transport service." ::= { snmp 1 } snmpOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages which were passed from the SNMP protocol entity to the transport service." ::= { snmp 2 } snmpInBadVersions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages which were delivered to the SNMP protocol entity and were for an unsupported SNMP version." ::= { snmp 3 } snmpInBadCommunityNames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages delivered to the SNMP protocol entity which used a SNMP community name not known to said entity." ::= { snmp 4 } snmpInBadCommunityUses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the Message." ::= { snmp 5 } snmpInASNParseErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP Messages." ::= { snmp 6 } -- { snmp 7 } is not used snmpInTooBigs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `tooBig'." ::= { snmp 8 } snmpInNoSuchNames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `noSuchName'." ::= { snmp 9 } snmpInBadValues OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `badValue'." ::= { snmp 10 } snmpInReadOnlys OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `readOnly'. It should be noted that it is a protocol error to generate an SNMP PDU which contains the value `readOnly' in the error-status field, as such this object is provided as a means of detecting incorrect implementations of the SNMP." ::= { snmp 11 } snmpInGenErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `genErr'." ::= { snmp 12 } snmpInTotalReqVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs." ::= { snmp 13 } snmpInTotalSetVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs." ::= { snmp 14 } snmpInGetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 15 } snmpInGetNexts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 16 } snmpInSetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Set-Request PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 17 } snmpInGetResponses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Response PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 18 } snmpInTraps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Trap PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 19 } snmpOutTooBigs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `tooBig.'" ::= { snmp 20 } snmpOutNoSuchNames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status is `noSuchName'." ::= { snmp 21 } snmpOutBadValues OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `badValue'." ::= { snmp 22 } -- { snmp 23 } is not used snmpOutGenErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `genErr'." ::= { snmp 24 } snmpOutGetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Request PDUs which have been generated by the SNMP protocol entity." ::= { snmp 25 } snmpOutGetNexts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Next PDUs which have been generated by the SNMP protocol entity." ::= { snmp 26 } snmpOutSetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Set-Request PDUs which have been generated by the SNMP protocol entity." ::= { snmp 27 } snmpOutGetResponses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Response PDUs which have been generated by the SNMP protocol entity." ::= { snmp 28 } snmpOutTraps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Trap PDUs which have been generated by the SNMP protocol entity." ::= { snmp 29 } snmpEnableAuthenTraps OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system. For JetDirect, this object is only implemented for agents which include a tcpip stack. This is generally the case, but with the advent of NOVELL only products this object will not be available." ::= { snmp 30 } -- The ATPort Group atportTable OBJECT-TYPE SYNTAX SEQUENCE OF AtportEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of AppleTalk ports for this entity." ::= { atport 1 } atportEntry OBJECT-TYPE SYNTAX AtportEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The description of one of the AppleTalk ports on this entity." INDEX { atportIndex } ::= { atportTable 1 } AtportEntry ::= SEQUENCE { atportIndex INTEGER, atportDescr DisplayString, atportType INTEGER, atportNetStart OCTET STRING (SIZE(2)), atportNetEnd OCTET STRING (SIZE(2)), atportNetAddress DdpAddress, atportStatus INTEGER, atportNetConfig INTEGER, atportZoneConfig INTEGER, atportZone OCTET STRING, atportIfIndex INTEGER } atportIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each AppleTalk port. Its value is between 1 and the total number of AppleTalk ports. The value for each port must remain constant at least from the re-initialization of the entity's network management system to the next re-initialization." ::= { atportEntry 1 } atportDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A text string containing information about the port. This string is intended for presentation to a human; it must not contain anything but printable ASCII characters." ::= { atportEntry 2 } atportType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following localtalk(2), ethertalk1(3), ethertalk2(4), tokentalk(5), iptalk(6), serial-ppp(7), serial-nonstandard(8), virtual(9) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of port, distinguished by the protocol immediately below DDP in the protocol stack." ::= { atportEntry 3 } atportNetStart OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) ACCESS read-write STATUS mandatory DESCRIPTION "The first AppleTalk network address in the range configured for this port. This is a two octet DDP network address in network byte order." ::= { atportEntry 4 } atportNetEnd OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) ACCESS read-write STATUS mandatory DESCRIPTION "The last AppleTalk network address in the range configured for this port. This is a two octet DDP network address in network byte order. If the network to which this AppleTalk port is connected is a Phase 1 network or a non-extended network, the value for atportNetEnd shall be two octets of zero." ::= { atportEntry 5 } atportNetAddress OBJECT-TYPE SYNTAX DdpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The AppleTalk network address configured for this port." ::= { atportEntry 6 } atportStatus OBJECT-TYPE SYNTAX INTEGER { operational(1), unconfigured(2), off(3), invalid(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The configuration status of this port. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry in the atportTable. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive from agents tabular information corresponding to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atportStatus object." ::= { atportEntry 7 } atportNetConfig OBJECT-TYPE SYNTAX INTEGER { configured(1), -- explicit configuration. garnered(2), -- assumed from inspection of net. guessed(3), -- a "random" configuration. unconfigured(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The configuration status of this port." ::= { atportEntry 8 } atportZoneConfig OBJECT-TYPE SYNTAX INTEGER { configured(1), -- explicit configuration garnered(2), -- assumed from inspection of net guessed(3), -- a "random" configuration. unconfigured(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The configuration status of the zone information for this port." ::= { atportEntry 9 } atportZone OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The zone name configured for this AppleTalk port." ::= { atportEntry 10 } atportIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The physical interface associated with this AppleTalk port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { atportEntry 11 } -- End of MIB-II objects -- Printer MIB prefixes -- printmib_oid[] = { 1,3,6,1,2,1,43}; -- printmib_oid_end[] = { 1,3,6,1,2,1,44}; -- Start HP proprietary objects -- The Status Group gdStatusBytes OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of valid bytes in the gdStatusEntry array." ::={ generalDeviceStatus 1 } gdStatusEntry OBJECT-TYPE SYNTAX OCTET STRING ACCESS not-accessible STATUS optional DESCRIPTION "The networked peripheral's 32 octet status information that is shared between the peripheral and the LAN card." ::={ generalDeviceStatus 2 } GdStatusEntry ::= SEQUENCE { gdStatusLineState INTEGER, gdStatusPaperState INTEGER, gdStatusInterventionState INTEGER, gdStatusNewMode INTEGER, gdStatusConnectionTerminationAck INTEGER, gdStatusPeripheralError INTEGER, gdStatusPaperOut INTEGER, gdStatusPaperJam INTEGER, gdStatusTonerLow INTEGER, gdStatusPagePunt INTEGER, gdStatusMemoryOut INTEGER, gdStatusIoActive INTEGER, gdStatusBusy INTEGER, gdStatusWait INTEGER, gdStatusInitialize INTEGER, gdStatusDoorOpen INTEGER, gdStatusPrinting INTEGER, gdStatusPaperOutput INTEGER, gdStatusReserved OCTET STRING, gdStatusNovBusy INTEGER, gdStatusLlcBusy INTEGER, gdStatusTcpBusy INTEGER, gdStatusAtBusy INTEGER } gdStatusLineState OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This describes the line state of the peripheral. When non-zero, the peripheral is off-line. When zero the peripheral is on-line." ::={ gdStatusEntry 1 } gdStatusPaperState OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This describes the state of the paper on the peripheral. When non-zero, the peripheral has a paper problem. When zero, the peripheral does not have a paper problem." ::={ gdStatusEntry 2 } gdStatusInterventionState OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This describes the intervention state of the peripheral. When non-zero, the peripheral requires human intervention to continue working. When zero, it requires no assistance." ::={ gdStatusEntry 3 } gdStatusNewMode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates to which read channel state the card should move. When non-zero, the card should indicate that the read channel is idle. When zero, the card should indicate that the read channel is operating. This object is Lan Manager io channel specific. It is kept here for backward compatibility." ::={ gdStatusEntry 4 } gdStatusConnectionTerminationAck OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates whether the peripheral is waiting for the Connection termination ACK. When non-zero, it is waiting. When zero, it is not waiting." ::={ gdStatusEntry 5 } gdStatusPeripheralError OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This is the error code from the peripheral." ::={ gdStatusEntry 6 } gdStatusPaperOut OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- PAPER-OUT-OR-PAPER-MOUNT(1), -- MANUAL-PAPER-FEED-NEEDED(2) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral is out of paper. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 8 } gdStatusPaperJam OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- PAPER-JAM(1) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral has a paper jam. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 9 } gdStatusTonerLow OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- TONER-LOW(1), -- NO-TONER-CARTRIDGE(2) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral has a low toner condition. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 10 } gdStatusPagePunt OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral did not receive data fast enough to keep up with the print engine when generating a page. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 11 } gdStatusMemoryOut OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral did not have enough memory to render an image on a page. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 12 } gdStatusIoActive OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral is processing data from this I/O interface card. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 13 } gdStatusBusy OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral is busy processing print/plot data. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 14 } gdStatusWait OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral is waiting for print/plot data to process. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 15 } gdStatusInitialize OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- INITIALIZING(1), -- WARM-UP(2) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral is initializing or warming up. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 16 } gdStatusDoorOpen OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral cover or door is open. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 17 } gdStatusPrinting OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- ORDINARY-PAGE(1), -- TEST-FONTS-CONFIG-OR-START-PAGE(2) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral is printing or otherwise marking or moving paper. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 18 } gdStatusPaperOutput OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- OUTPUT-STORAGE-FULL(1) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the peripheral has a paper output problem such as the output storage bin being full. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::={ gdStatusEntry 19 } gdStatusReserved OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..13)) ACCESS read-only STATUS optional DESCRIPTION "This is the reserved area that is not currently used, but will allow for growth within the gdStatusEntry table." ::={ gdStatusEntry 20 } gdStatusNovBusy OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates if this channel is active. If the value is 0 then this channel is active or the peripheral is idle. If this value is non-zero then another channel is active. This is the Novell io channel" ::={ gdStatusEntry 21 } gdStatusLlcBusy OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates if this channel is active. If the value is 0 then this channel is active or the peripheral is idle. If this value is non-zero then another channel is active. This is the LLC io channel" ::={ gdStatusEntry 22 } gdStatusTcpBusy OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates if this channel is active. If the value is 0 then this channel is active or the peripheral is idle. If this value is non-zero then another channel is active. This is the TCP io channel" ::={ gdStatusEntry 23 } gdStatusAtBusy OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates if this channel is active. If the value is 0 then this channel is active or the peripheral is idle. If this value is non-zero then another channel is active. This is the Apple talk io channel" ::={ gdStatusEntry 24 } gdStatusDisplay OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "The string diplayed on the peripheral front panel. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this is always a zero length string." ::={ generalDeviceStatus 3 } gdStatusJobName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "The current job name set by the peripheral. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this is always a zero length string." ::={ generalDeviceStatus 4 } gdStatusSource OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "A string indicating the name of the physical port or protocol the printer is currently getting data from." ::={ generalDeviceStatus 5 } gdStatusPapstatus OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "A string indicating the Appletalk papstatus response." ::={ generalDeviceStatus 6 } gdStatusId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "A formatted string describing this peripheral." ::={ generalDeviceStatus 7 } gdStatusDisplayCode OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This is the display code that the peripheral uses to tell the card what type of display the front panel of the printer is." ::={ generalDeviceStatus 8 } gdStatusNlsCode OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This value is the representation of what native language the printer is in currently." ::={ generalDeviceStatus 9 } gdStatusJobTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This value represents (in seconds) the maximum time of inactivity which must elapse before the JetDirect card switches from the current network protocol to another when a normal end of job is not detected." ::={ generalDeviceStatus 10 } gdStatusPjlUstatus OBJECT-TYPE SYNTAX INTEGER -- DISABLED(0), -- ENABLED(1) ACCESS read-write STATUS optional DESCRIPTION "This object will enable/disable PJL ustatus." ::={ generalDeviceStatus 11 } gdStatusLaaSupport OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This value represents what protocols Locally Administered addressing is supported over. This is currently 0 for 802.3 cards and 7 for 802.5 cards. LAA is not supported on 802.3. The value is a mask of bits, 1 for each of the protocols below. +-----------------------------------------------+ | NA | NA | NA | NA | NA | TCP | LLC | NOV | +-----------------------------------------------+" ::={ generalDeviceStatus 12 } gdPasswords OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) ACCESS read-write STATUS optional DESCRIPTION "This object is used as a 256 byte NVRAM area for JetAdmin. It is completely managed by JetAdmin. Initially it is initialized to all zeros. A coldboot will re-initialize to all zeros." ::={ generalDeviceStatus 13 } -- the following objects are not supported after EX+3. -- They were moved to the npPort sub-tree. In the EX+3 box, -- they appear in both sub-trees. npPortNumPorts OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "iThe number of peripheral interfaces supported by this device " ::={ generalDeviceStatus 14 } npPortType OBJECT-TYPE SYNTAX INTEGER -- unknown(1), -- MIO(2), -- XIO(3), -- parallel(4), -- Centronics(5), -- Bitronics(6), -- ECP(7), -- serial(8), -- SCSI(9) -- MIO2(10) ACCESS read-only STATUS optional DESCRIPTION "The type of the peripheral interface. A parallel port will return the specific protocl currently in use. If the parallel port is disconnected it will return parallel(4)." ::={ generalDeviceStatus 15 } npSysModelNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-only STATUS optional DESCRIPTION "The HP model number of the device." ::={ generalDeviceStatus 16 } npSysNetworkConnectors OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This object describes the network connectors supported by the device. The value is a bit mask. A set bit indicates the connector is supported. Bit Value Connector 0 0x01 Ethernet, BNC 1 0x02 Ethernet, AUI 2 0x04 Ethernet, RJ-45 3 0x08 TokenRing, DB-9 4 0x10 TokenRing, RJ-45 5 0x20 LocalTalk" ::={ generalDeviceStatus 17 } ----------- -- These are new objects I am adding for EX+3. They need to -- get merged in above eventually. -- Additions to the gdStatus tree. -- These objects are only present in EX+3. -- The OIDs are temporary. I would prefer to use 14 and 15 once the obsolete -- objects with those OIDs are removed from the code. XXX gdStatusAtPrinterName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) ACCESS read-write STATUS optional DESCRIPTION "The AppleTalk name of the printer." ::={ generalDeviceStatus 18 } gdStatusAtPrinterType OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) ACCESS read-only STATUS optional DESCRIPTION "The AppleTalk type of the printer." ::={ generalDeviceStatus 19 } -- the netPrinterType group LJ5SI OBJECT IDENTIFIER ::={ netPrinterType 1 } LJ5M OBJECT IDENTIFIER ::={ netPrinterType 2 } LJ6P OBJECT IDENTIFIER ::={ netPrinterType 3 } LJ4000 OBJECT IDENTIFIER ::={ netPrinterType 5 } LJ5000 OBJECT IDENTIFIER ::={ netPrinterType 6 } LJ8000 OBJECT IDENTIFIER ::={ netPrinterType 9 } -- PML prefixes -- pml_oid[] = { 1,3,6,1,4,1,11,2,3,9,4,2 }; -- pml_trap_enable_oid[] = { 1,3,6,1,4,1,11,2,3,9,4,1,1,0 }; -- pml_trap_disable_oid[] = { 1,3,6,1,4,1,11,2,3,9,4,1,2,0 }; -- pml_magic_oid[] = { 1,3,6,1,4,1,11,2,3,9,4,2,99,1,0 } -- Printer MIB prefixes -- printmib_channel_number[] = {1,3,6,1,4,1,11,2,3,9,4,2,1,6,1,0} -- printmib_trap_oid[] = { 1,3,6,1,4,1,11,2,3,9,4,2,1,6,2,0} -- printmib_channel_table[5][17] = { -- {1,3,6,1,4,1,11,2,3,9,4,2,1,6,3,1,2}, -- {1,3,6,1,4,1,11,2,3,9,4,2,1,6,3,1,3}, -- {1,3,6,1,4,1,11,2,3,9,4,2,1,6,3,1,4}, -- {1,3,6,1,4,1,11,2,3,9,4,2,1,6,3,1,5}, -- {1,3,6,1,4,1,11,2,3,9,4,2,1,6,3,1,6},} -- End Printer MIB prefixes -- the Ieee8023Mac group ieee8023MacTable OBJECT-TYPE SYNTAX SEQUENCE OF Ieee8023MacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of ieee8023MacEntry entries." ::= { ieee8023Mac 1 } ieee8023MacEntry OBJECT-TYPE SYNTAX Ieee8023MacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing the hp ieee8023 extentions." INDEX { ieee8023MacIndex } ::= { ieee8023MacTable 1 } Ieee8023MacEntry ::= SEQUENCE { ieee8023MacIndex INTEGER, ieee8023MacTransmitteds Counter, ieee8023MacNotTransmitteds Counter, ieee8023MacDeferreds Counter, ieee8023MacCollisions Counter, ieee8023MacSingleCollisions Counter, ieee8023MacMultipleCollisions Counter, ieee8023MacExcessCollisions Counter, ieee8023MacLateCollisions Counter, ieee8023MacCarrierLostErrors Counter, ieee8023MacNoHeartBeatErrors Counter, ieee8023MacFramesReceiveds Counter, ieee8023MacUndeliverableFramesReceiveds Counter, ieee8023MacCrcErrors Counter, ieee8023MacAlignmentErrors Counter, ieee8023MacResourceErrors Counter, ieee8023MacControlFieldErrors Counter, ieee8023MacUnknownProtocolErrors Counter, ieee8023MacMulticastsAccepteds Counter, --ieee8023MacMulticastsAccepteds -- Counter, ieee8023MacInfiniteDeferrals Counter, ieee8023MacUnderflowErrors Counter, ieee8023MacNoResources Counter, ieee8023MacLengthErrors Counter } ieee8023MacIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface/port to which this entry is applicable. The interface/port identified by a particular value of this index is the same interface/port as identified by the same value of ifIndex." ::= { ieee8023MacEntry 1 } ieee8023MacTransmitteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames successfully transmitted." ::= { ieee8023MacEntry 2 } ieee8023MacNotTransmitteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames not transmitted." ::= { ieee8023MacEntry 3 } ieee8023MacDeferreds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of frames which were successfully transmitted after a deferral. If any collisions occurred before transmission, xmtDeferredTransmission isn't incremented." ::= { ieee8023MacEntry 4 } ieee8023MacCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of transmit attempts that were retransmitted due to collisions, and are subsequently transmitted successfully." ::= { ieee8023MacEntry 5 } ieee8023MacSingleCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmit attempts that are involved in a single collision, and are subsequently transmitted successfully." ::= { ieee8023MacEntry 6 } ieee8023MacMultipleCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmit attempts that are involved in between one and fifteen collision attempts, and are subsequently transmitted successfully." ::= { ieee8023MacEntry 7 } ieee8023MacExcessCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of transmits that occur after more than 15 collisions, and are subsequently transmitted successfully." ::= { ieee8023MacEntry 8 } ieee8023MacLateCollisions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of collisions that occured after one end-to-end frame propagation delay." ::= { ieee8023MacEntry 9 } ieee8023MacCarrierLostErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of times that carrier sense was lost when attempting to transmit." ::= { ieee8023MacEntry 10 } ieee8023MacNoHeartBeatErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times the MAU failed to assert SQE after transmitting a packet." ::= { ieee8023MacEntry 11 } ieee8023MacFramesReceiveds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames successfully received." ::= { ieee8023MacEntry 12 } ieee8023MacUndeliverableFramesReceiveds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received that could not be delivered because the software buffer was overrun when frames were sent faster than they could be received." ::= { ieee8023MacEntry 13 } ieee8023MacCrcErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of Cyclical Redundancy Check (CRC) errors detected." ::= { ieee8023MacEntry 14 } ieee8023MacAlignmentErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received that were both misaligned and had bad CRC." ::= { ieee8023MacEntry 15 } ieee8023MacResourceErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received that were lost due to lack of resources." ::= { ieee8023MacEntry 16 } ieee8023MacControlFieldErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received with errors in the control field." ::= { ieee8023MacEntry 17 } ieee8023MacUnknownProtocolErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number frames dropped because the type field or sap field referenced an invalid protocol." ::= { ieee8023MacEntry 18 } ieee8023MacMulticastsAccepteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of accepted muliticast addresses." ::= { ieee8023MacEntry 19 } ieee8023MacInfiniteDeferrals OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames not transmitted successfully due to excessive number of deferrals." ::= { ieee8023MacEntry 20 } ieee8023MacUnderflowErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames not transmitted successfully because an underflow occurred on the transmit." ::= { ieee8023MacEntry 21 } ieee8023MacNoResources OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames not transmitted successfully because the MAC lacked resources to handle the frame." ::= { ieee8023MacEntry 22 } ieee8023MacLengthErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received that have length errors." ::= { ieee8023MacEntry 23 } -- The 802.3 Multicast Address Table ieee8023MacMcaTable OBJECT-TYPE SYNTAX SEQUENCE OF Ieee8023MacMcaTableEntry ACCESS not-accessible STATUS optional DESCRIPTION "The 802.3 multicast address table." ::= { ieee8023Mac 2 } ieee8023MacMcaTableEntry OBJECT-TYPE SYNTAX Ieee8023MacMcaTableEntry ACCESS not-accessible STATUS optional DESCRIPTION "Entries in the ieee8023MacMcaTable." INDEX { ieee8023MacMcaIndex } ::= { ieee8023MacMcaTable 1 } Ieee8023MacMcaTableEntry ::= SEQUENCE { ieee8023MacMcaIndex INTEGER, ieee8023MacMcaAddress OCTET STRING } ieee8023MacMcaIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The index corresponding to a particular instance in the ieee8023MacMcaTable." ::= { ieee8023MacMcaTableEntry 1 } ieee8023MacMcaAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "The multicast address of a particular instance in the ieee8023McaTable." ::= { ieee8023MacMcaTableEntry 2 } -- Other 802.3 Objects ieee8023MacState OBJECT-TYPE SYNTAX INTEGER { offline(1), initializing(2), online(4), error(5), io-not-ready(6) } ACCESS read-only STATUS optional DESCRIPTION "A state variable that indicates the current state of the MAC driver." ::= { ieee8023Mac 3 } ieee8023MacConfigurationStatus OBJECT-TYPE SYNTAX INTEGER { internal-mau-selected1(1), internal-mau-selected5(5), internal-mau-selected13(13), external-mau-selected(14) } ACCESS read-only STATUS optional DESCRIPTION "These are the four bits of hardware power sense and jumper sense registers: 15 14 13 12 11 +---+---+---+---+----------+ |apa|mpa|ext|int| unused | +---+---+---+---+----------+ unused Reserved for future status. apa 12v power detected at the AUI connector. mpa 12v power detected at the Peripheral interface. ext External AUI connector selected. int Internal tranceiver selected." ::= { ieee8023Mac 4 } ieee8023MacNumberActiveMCAs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of entries in the multicast address table." ::= { ieee8023Mac 5 } -- .1.3.6.1.4.1.11.2.4.1.6.0 ieee8023MacMauType OBJECT-TYPE SYNTAX INTEGER { unknownOrOther(1), aui(2), a10BASE-5(3), foirl(4), a10BASE-2(5), a10BASE-TDuplexModeUnknown(6), a10BASE-FP(7), a10BASE-FB(8), a10BASE-FL-duplex-mode-unknown(9), a10BROAD36(10), a10BASE-T-half-duplex-mode(11), a10BASE-T-full-duplex-mode(12), a10BASE-FL-half-duplex-mode(13), a10BASE-FL-full-duplex-mode(14), a100BASE-T4(15), a100BASE-TX-half-duplex-mode(16), a100BASE-TX-full-duplex-mode(17), a100BASE-FX-half-duplex-mode(18), a100BASE-FX-full-duplex-mode(19), a100BASE-T2-half-duplex-mode(20), a100BASE-T2-full-duplex-mode(21) } ACCESS read-only STATUS optional DESCRIPTION "This object identifies the 10 or 100 Mb/s MAU type. It represents the operational type of the MAU, as determined by (1) auto-negotiation, (2) manual configuration, or (3) port selection logic." ::= { ieee8023Mac 6 } -- .1.3.6.1.4.1.11.2.4.1.7.0 ieee8023MacJackType OBJECT-TYPE SYNTAX INTEGER { other(1), rj45(2), rj45S(3), -- RJ45 shielded db9(4), bnc(5), faui(6), -- female AUI maui(7), -- male AUI fiberSC(8), fiberMIC(9), fiberST(10), telco(11) } ACCESS read-only STATUS optional DESCRIPTION "Jack type associated with the selected MAU type." ::= { ieee8023Mac 7 } -- .1.3.6.1.4.1.11.2.4.1.8.0 ieee8023MacMauAutoNegAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS optional DESCRIPTION "This object indicates whether the interface with auto-negotiation signaling has this ability enabled." ::= { ieee8023Mac 8 } -- the Ieee8025Mac group ieee8025MacTable OBJECT-TYPE SYNTAX SEQUENCE OF Ieee8025MacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of ieee8025MacEntry entries." ::= { ieee8025Mac 1 } ieee8025MacEntry OBJECT-TYPE SYNTAX Ieee8025MacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing the hp ieee8025 extentions." INDEX { ieee8025MacIndex } ::= { ieee8025MacTable 1 } Ieee8025MacEntry ::= SEQUENCE { ieee8025MacIndex INTEGER, ieee8025MacTransmitteds Counter, ieee8025MacUnderflowErrors Counter, ieee8025MacNoResources Counter, ieee8025MacFramesReceiveds Counter, ieee8025MacLineErrors Counter, ieee8025MacBurstErrors Counter, ieee8025MacFSSetErrors Counter, ieee8025MacCongestions Counter, ieee8025MacLostFrameErrors Counter, ieee8025MacFrameCopiedErrors Counter, ieee8025MacTooLongErrors Counter, ieee8025MacLengthErrors Counter, ieee8025MacOverflowErrors Counter, ieee8025MacTokenErrors Counter } ieee8025MacIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface/port to which this entry is applicable. The interface/port identified by a particular value of this index is the same interface/port as identified by the same value of ifIndex." ::= { ieee8025MacEntry 1 } ieee8025MacTransmitteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames successfully transmitted." ::= { ieee8025MacEntry 2 } ieee8025MacUnderflowErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames not transmitted due to underflow errors." ::= { ieee8025MacEntry 3 } ieee8025MacNoResources OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames which were not transmitted due to no outbound resources. " ::= { ieee8025MacEntry 4 } ieee8025MacFramesReceiveds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames received." ::= { ieee8025MacEntry 5 } ieee8025MacLineErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of received line error frames." ::= { ieee8025MacEntry 6 } ieee8025MacBurstErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of received burst errors." ::= { ieee8025MacEntry 7 } ieee8025MacFSSetErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of received FS set errors." ::= { ieee8025MacEntry 8 } ieee8025MacCongestions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of received congestion packets." ::= { ieee8025MacEntry 9 } ieee8025MacLostFrameErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of received lost frame errors." ::= { ieee8025MacEntry 10 } ieee8025MacFrameCopiedErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of received frame copied errors." ::= { ieee8025MacEntry 11 } ieee8025MacTooLongErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number received too long errors." ::= { ieee8025MacEntry 12 } ieee8025MacLengthErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of recevied length errors." ::= { ieee8025MacEntry 13 } ieee8025MacOverflowErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of received overflow errors." ::= { ieee8025MacEntry 14 } ieee8025MacTokenErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of token errors." ::= { ieee8025MacEntry 15 } -- The 802.5 Multicast Address Table ieee8025MacMcaTable OBJECT-TYPE SYNTAX SEQUENCE OF Ieee8025MacMcaTableEntry ACCESS not-accessible STATUS optional DESCRIPTION "The 802.5 multicast address table." ::= { ieee8025Mac 2 } ieee8025MacMcaTableEntry OBJECT-TYPE SYNTAX Ieee8025MacMcaTableEntry ACCESS not-accessible STATUS optional DESCRIPTION "Entries in the ieee8025MacMcaTable." INDEX { ieee8025MacMcaIndex } ::= { ieee8025MacMcaTable 1 } Ieee8025MacMcaTableEntry ::= SEQUENCE { ieee8025MacMcaIndex INTEGER, ieee8025MacMcaAddress OCTET STRING } ieee8025MacMcaIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The index corresponding to a particular instance in the ieee8025MacMcaTable." ::= { ieee8025MacMcaTableEntry 1 } ieee8025MacMcaAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "The multicast address of a particular instance in the ieee8025McaTable." ::= { ieee8025MacMcaTableEntry 2 } -- Other 802.5 Objects ieee8025MacState OBJECT-TYPE SYNTAX INTEGER -- OFFLINE(1), -- INITIALIZING(2), -- ONLINE(4), -- ERROR(5), -- IO_NOT_READY(6) ACCESS read-only STATUS optional DESCRIPTION "A state variable that indicates the current state of the MAC driver." ::= { ieee8025Mac 3 } ieee8025MacConfigurationStatus OBJECT-TYPE SYNTAX INTEGER -- INTERNAL_MAU_SELECTED1(1), -- INTERNAL_MAU_SELECTED5(5), -- INTERNAL_MAU_SELECTED13(13), -- EXTERNAL_MAU_SELECTED(14) ACCESS read-only STATUS optional DESCRIPTION "These are the four bits of hardware power sense and jumper sense registers: 15 14 13 12 11 +---+---+---+---+----------+ |apa|mpa|ext|int| unused | +---+---+---+---+----------+ unused Reserved for future status. apa 12v power detected at the AUI connector. mpa 12v power detected at the Peripheral interface. ext External AUI connector selected. int Internal tranceiver selected." ::= { ieee8025Mac 4 } ieee8025MacNumberActiveMCAs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of entries in the multicast address table." ::= { ieee8025Mac 5 } -- The HP Network Peripheral Card (npCard) Group -- The System subgroup of npCard npSysState OBJECT-TYPE SYNTAX INTEGER { offline(1), initializing(2), online(4), error(5), io-not-ready(6) } ACCESS read-only STATUS optional DESCRIPTION "The state of the LAN card to network peripheral interface driver." ::={ npSys 1 } npSysStatusMessage OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "A status string reflecting the current state of the card and peripheral." ::={ npSys 2 } npSysPeripheralFatalError OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The most recent peripheral fatal error that is being displayed on the peripheral's display panel. The error typically appears as a '80 Service (00xx)' error. Refer to peripheral documentation to determine what the error means." ::={ npSys 3 } npSysCardFatalError OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The most recent LAN Card error that is being displayed on the peripheral's display panel. The error typically appears as a '80 Service (01xx)' error. Refer to peripheral documentation to determine what the error means." ::={ npSys 4 } npSysMaximumWriteBuffers OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The maximum number of write buffers configured for the LAN card (this translates to the write window size of the connection)." ::={ npSys 5 } npSysMaximumReadBuffers OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The maximum number of read buffers configured for the LAN card (this translates to the read window size of the connection)." ::={ npSys 6 } npSysTotalBytesRecvs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The total number of bytes received since reset." ::={ npSys 7 } npSysTotalBytesSents OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The total number of bytes sent since reset." ::={ npSys 8 } npSysCurrReadReq OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS optional DESCRIPTION "The current number of read data buffers owned by the LAN card." ::={ npSys 9 } -- Additions to the npSys tree. (for EX+3) npSysModelNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-only STATUS optional DESCRIPTION "The HP model number of the device." ::={ npSys 10 } npSysNetworkConnectors OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This object describes the network connectors supported by the device. The value is a bit mask. A set bit indicates the connector is supported. Bit Value Connector 0 0x01 Ethernet, BNC 1 0x02 Ethernet, AUI 2 0x04 Ethernet, RJ-45 3 0x08 TokenRing, DB-9 4 0x10 TokenRing, RJ-45 5 0x20 LocalTalk 6 0x40 100VG, RJ-45 7 0x80 100T, RJ-45" ::={ npSys 11 } npSysStatusPage OBJECT-TYPE SYNTAX SEQUENCE OF NpSysStatusPageLine ACCESS not-accessible STATUS optional DESCRIPTION "A table of all the lines which the card prints on the self-test page." ::={ npSys 12 } npSysStatusPageLine OBJECT-TYPE SYNTAX NpSysStatusPageLine ACCESS not-accessible STATUS optional DESCRIPTION "An entry containing one line of the status page." INDEX { npSysStatusPageIndex } ::={ npSysStatusPage 1 } NpSysStatusPageLine ::= SEQUENCE { npSysStatusPageIndex INTEGER, npSysStatusPageText OCTET STRING } npSysStatusPageIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The index value of this entry in the table." ::={ npSysStatusPageLine 1 } npSysStatusPageText OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "The text of one line of the card status. This is the same text that is shown on the printer's selftest page. The text is localized." ::={ npSysStatusPageLine 2 } npSysManufactureInfo OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "This object provides information about the hardware that the firmware is running on as well as manufacturing codes." ::={ npSys 13 } npSysPeekAddress OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This object specifies an address for subsequent peeks." ::={ npSys 14 } npSysPeek OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "This object specifies an address for subsequent peeks." ::={ npSys 15 } -- The following 2 objects are from the original Lan Manager MIB. They -- need to exist for backward compatibility. npCardPFatalErr OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The most recent peripheral fatal error that is being displayed on the peripheral's display panel. The error typically appears as a '80 Service (00xx)' error. Refer to peripheral documentation to determine what the error means." ::={ npCard 2 } npCardIoFatalErr OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The most recent LAN Card error that is being displayed on the peripheral's display panel. The error typically appears as a '80 Service (01xx)' error. Refer to peripheral documentation to determine what the error means." ::={ npCard 3 } --- The Card Connection Statistics subgroup of npCard npConnsAccepts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of connections accepted since reset." ::={ npConns 1 } npConnsRefuseds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of connections refused since reset. Connections are refused for the following reasons: a connection is already active, the peripheral is offline, the network peripheral interface is not ready for connections after a power-up or reset, or there isn't enough buffer space on the card to establish a connection." ::={ npConns 2 } npConnsDenys OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of connections that the card denied due to failure to match the access list." ::={ npConns 3 } npConnsDenysIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "The IP address of the last node to be denied a connection due to failure to match the access list." ::={ npConns 4 } npConnsAborts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of connections aborted due to a network problem." ::={ npConns 5 } npConnsAbortReason OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS optional DESCRIPTION "The textual description of why the last abort on the card occurred." ::={ npConns 6 } npConnsAbortIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "The IP address of the last node to establish a connection before the card aborted." ::={ npConns 7 } npConnsAbortPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS optional DESCRIPTION "The port of the last node to establish a connection before the card aborted." ::={ npConns 8 } npConnsAbortTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS optional DESCRIPTION "The time (in hundredths of a second) since the last time the card was aborted." ::={ npConns 9 } npConnsState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } ACCESS read-only STATUS optional DESCRIPTION "State of current connection to card." ::={ npConns 10 } npConnsIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "Remote IP address of the node currently connected to the card. Zero if no connection is active." ::={ npConns 11 } npConnsPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS optional DESCRIPTION "Remote port number of the node currently connected to the card. Zero if no connection is active." ::={ npConns 12 } npConnsPeriphClose OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of connections closed in response to a peripheral request I/O channel reset request." ::={ npConns 13 } npConnsIdleTimeouts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of connections closed due to an idle timeout." ::={ npConns 14 } npConnsNmClose OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of connections closed by SetRequests to the MIB variable, npCtlCloseConnection." ::={ npConns 15 } npConnsBytesRecvds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of bytes received by this connection." ::={ npConns 16 } npConnsBytesSents OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of bytes transmitted by this connection." ::={ npConns 17 } --- The Card Configuration subgroup of npCard -- npCfgSource defined below -- We changed the enumeration and added new values. npCfgSource OBJECT-TYPE SYNTAX INTEGER { -- bootp(0), historical only manual-one(1), -- read-only, depreciate after intro of box products. bootp-two(2), -- read-only, depreciate after intro of box products. manual-three(3), -- read/write, must write ip_addr in same packet. bootp-four(4), -- read/write, ignores other npCfg if in same packet. dhcp(5), -- read/write, ignores other npCfg if in same packet. not-configured(6), -- read-only default-config(7), -- read-only rarp(8) -- read-only } ACCESS read-write STATUS mandatory DESCRIPTION "This object indicates how the device obtained its IP configuration." ::={ npCfg 1 } npCfgYiaddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS optional DESCRIPTION "The IP address assigned to the card from the BOOTP reply yiaddr field." ::={ npCfg 2 } npCfgSiaddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "The IP address of the TFTP server from the BOOTP reply siaddr field." ::={ npCfg 3 } npCfgGiaddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "The IP address of the TFTP gateway from the BOOTP reply giaddr field." ::={ npCfg 4 } npCfgLogServer OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "The IP address of the Log Server from the BOOTP reply Tag: 7 field." ::={ npCfg 5 } npCfgSyslogFacility OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This specifies the facility identifier used in syslog messages generated by the card." ::={ npCfg 6 } npCfgAccessState OBJECT-TYPE SYNTAX INTEGER { allowed(1), not-allowed(2) } ACCESS read-only STATUS optional DESCRIPTION "An indication of whether or not the requesting host is allowed to connect to the card as dictated by the access list." ::={ npCfg 7 } npCfgAccessListNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of access list entries." ::={ npCfg 8 } npCfgAccessListTable OBJECT-TYPE SYNTAX SEQUENCE OF AccessListEntry ACCESS not-accessible STATUS optional DESCRIPTION "List of access addresses and masks." ::={ npCfg 9 } accessListEntry OBJECT-TYPE SYNTAX AccessListEntry ACCESS not-accessible STATUS optional DESCRIPTION "Each entry contains an access address and mask." INDEX { npCfgAccessListIndex } ::={ npCfgAccessListTable 1 } AccessListEntry ::= SEQUENCE { npCfgAccessListIndex INTEGER, npCfgAccessListAddress IpAddress, npCfgAccessListAddrMask IpAddress } npCfgAccessListIndex OBJECT-TYPE SYNTAX INTEGER (0..9) ACCESS read-only STATUS optional DESCRIPTION "Index to the configuration access list table." ::={ accessListEntry 1 } npCfgAccessListAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "Address to compare with after applying the wildcard to the requestor's address." ::={ accessListEntry 2 } npCfgAccessListAddrMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "Address mask used to help determine whether or not a given IP address is allowed access to the card. An IP address is allowed access if (Addr & AddrMask) == (IP & AddrMask)." ::={ accessListEntry 3 } npCfgIdleTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The idle timeout is the length in seconds after which an idle connection is terminated. A value of zero disables the timeout." ::={ npCfg 10 } --npCfgLocalSubnets OBJECT-TYPE (replace in bunker) -- SYNTAX INTEGER -- none(0), -- exist(1) -- ACCESS read-only -- STATUS optional -- DESCRIPTION -- "An indication of whether or not the card recognizes -- any local subnets." -- ::={ npCfg 11 } --.1.3.6.1.4.1.11.2.4.3.5.11.0 (new in bunker) npCfgTcpMss OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Enumerate as follows: 0 = treat all hosts as local which means JetDirect sends a maximum of 1460 bytes of data in all outbound packets. 1 = treat hosts on different subnets but in the same network as local which means for hosts in the same network, send 1460 bytes; else send 536 bytes in outbound packets. 2 = treat only hosts on the same network and same subnet as local (use 1460 bytes); otherwise treat them as remote hosts (send 536 bytes)." ::={ npCfg 11 } -- These objects are present in EX+3 -- added into the master mib on 9/8/95 npCfgSubnetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS optional DESCRIPTION "The subnet mask associated with the IP address of this card." ::= { npCfg 12} npCfgDefaultGateway OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS optional DESCRIPTION "This variable contains the IP address of the default router for this card." ::= { npCfg 13} -- redirector objects removed in bunker npCfg 14, 15,16 --npCfgRootURL OBJECT-TYPE -- SYNTAX OCTET STRING -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "The HTTP root(/) directory redirect location." -- ::= { npCfg 14} --npCfgGenURL OBJECT-TYPE -- SYNTAX OCTET STRING -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "The HTTP /redirect directory location." -- ::= { npCfg 15} --npCfgDomainName OBJECT-TYPE -- SYNTAX OCTET STRING -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "The JetDirect domain name as configured by Web JetAdmin." -- ::= { npCfg 16} -- .1.3.6.1.4.1.11.2.4.3.5.17.0 npCfgSlpTtl OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The TTL value is used in the IP header of SLP multicast pkts sent by JetDirect. " ::= { npCfg 17 } -- .1.3.6.1.4.1.11.2.4.3.5.18.0 npCfgIPP OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The value can be 0, meaning IPP has been disabled, or 1, meaning IPP has been enabled." ::= { npCfg 18 } -- The TCP subgroup of npCard npTcpInSegInOrders OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of TCP segments received in order." ::={ npTcp 1 } npTcpInSegOutOfOrders OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of TCP segments received out of order." ::={ npTcp 2 } npTcpInSegZeroProbes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of TCP zero window probes received." ::={ npTcp 3 } npTcpInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "The number of TCP segments received that were discarded." ::={ npTcp 4 } -- The Card Control subgroup of npCard npCtlReconfigIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "The IP address of the last node to request a reconfig of the card. This value is preserved across a reconfig." ::={ npCtl 1 } npCtlReconfigPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS optional DESCRIPTION "The port of the last node to request a reconfig of the card. This value is preserved across a reconfig." ::={ npCtl 2 } npCtlReconfigTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS optional DESCRIPTION "The time (in hundredths of a second) since the last time the card was reconfigured." ::={ npCtl 3 } npCtlCloseIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS optional DESCRIPTION "The IP address of the last node to request a close of the peripheral data connection on the card. This value is cleared on a reconfig." ::={ npCtl 4 } npCtlClosePort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS optional DESCRIPTION "The port of the last node to request a close of the peripheral data connection on the card. This value is cleared on a reconfig." ::={ npCtl 5 } npCtlImageDump OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- DUMP(1) ACCESS read-write STATUS optional DESCRIPTION "Writing a one (1) to this variable causes the card to dump its RAM image into a file using TFTP. The file is dumped onto the BOOTP server machine whose IP address is in the MIB variable, npCfgSiaddr { npCfg 3 }. The file name is: npi. in the tftp directory, where is the IP address of the card. The file must be writable by TFTP." ::= { npCtl 6 } npCtlCloseConnection OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- CLOSE(1) ACCESS read-write STATUS optional DESCRIPTION "Writing a one (1) to this variable causes the card to close the current peripheral data connection" ::= { npCtl 7 } npCtlReconfig OBJECT-TYPE SYNTAX INTEGER -- OFF(0), -- REBOOT(1) ACCESS read-write STATUS optional DESCRIPTION "Writing any value to this variable causes the card to reconfigure itself by doing the BOOTP/TFTP configuration activity." ::= { npCtl 8 } npCtlProtocolSet OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This is a 4 byte integer value. The least significant bytes represent the protocols on the card. A value of '1' indicates a protocol that is enabled. A value of '0' indicates a protocol that is disabled. The 32-bit protocol enable 'structure' is defined as: bits 31-28: Number of I/O channels/protocols present (NUM_CHAN) bits 27-24: Number of I/O channels which may operate concurrently (NUM_OP_CHAN) bits 23-16: unused, reserved bits 15-1: Individual I/O channel/protocol enable bits, 0 == disable, 1 == enable MIO_IOCHAN_NOVELL bit 1 MIO_IOCHAN_LLC bit 2 MIO_IOCHAN_TCP bit 3 MIO_IOCHAN_ATALK bit 4 bit 0: When NUM_OP_CHAN == 1, auto-protocol select enable bit, 0 == disable, 1 == enable (APS_ON)" ::={ npCtl 9 } -- added for EX+3 npCtlStatusPageLang OBJECT-TYPE SYNTAX INTEGER { pcl(1), ascii(2), postscript(3), hpgl(4) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies the PDL used to print the status page." ::= { npCtl 10 } npCtlPrintStatusPage OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Writing any value to this object causes the device to print a status page." ::= { npCtl 11 } npCtlErrorBehavior OBJECT-TYPE SYNTAX INTEGER { -- not-supported-on-this-platform(0), mib compiler will not take zero dump-then-reboot(1), reboot-without-dump(2), dump-then-halt(3), halt-without-dump(4), deliberate-panic(256), cold-reset-novram(512), deliberate-restart(1024) } ACCESS read-write STATUS optional DESCRIPTION "This object provides management capability to specify various error/panic/reset modes as are enumerated above. Default is halt_without-dump(4)." ::= { npCtl 12 } npCtlCrcControl OBJECT-TYPE SYNTAX INTEGER { -- off(0), mib compiler will not take zero on(1) } ACCESS read-write STATUS optional DESCRIPTION "This object controls and manages the collection of crc data for paperless print testing." ::= { npCtl 13 } -- The HP Modular Input/Output (MIO) subgroup of npCard -- The Card Status Entry npNpiCardStatusEntry OBJECT-TYPE SYNTAX SEQUENCE OF NpNpiCardStatusEntry ACCESS not-accessible STATUS optional DESCRIPTION "These are the set of status bytes that the peripheral passes to the network card. The peripheral and LAN card exchange these status bytes whenever an event causes the status to change." ::={ npNpi 1 } NpNpiCardStatusEntry ::= SEQUENCE { npNpiCseDataState INTEGER, npNpiCseErrorCode INTEGER, npNpiCseLinkEvent INTEGER, npNpiCseReadMode INTEGER, npNpiCseWriteMode INTEGER, npNpiCseWarningCode INTEGER, npNpiCseConnectionState INTEGER, npNpiCseNovWarningCode INTEGER, npNpiCseLlcWarningCode INTEGER, npNpiCseTcpWarningCode INTEGER, npNpiCseAtkWarningCode INTEGER } npNpiCseDataState OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The data state of the LAN card." ::={ npNpiCardStatusEntry 1 } npNpiCseErrorCode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The LAN card's error code." ::={ npNpiCardStatusEntry 2 } npNpiCseLinkEvent OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The LAN link event (reset or initialized or triggered)." ::={ npNpiCardStatusEntry 3 } npNpiCseReadMode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The state of the LAN card's read channel (operate or idle)." ::={ npNpiCardStatusEntry 4 } npNpiCseWriteMode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The state of the LAN card's write channel (operate or idle)." ::={ npNpiCardStatusEntry 5 } npNpiCseWarningCode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the LAN card channel zero has encountered an error condition which isn't serious enough to shut the peripheral down, but should be checked out." ::={ npNpiCardStatusEntry 6 } npNpiCseConnectionState OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "Indicates whether or not the peripheral is currently connected to a server." ::={ npNpiCardStatusEntry 7 } npNpiCseNovWarningCode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the Novell stack has encountered an error condition which isn't serious enough to shut the peripheral down, but should be checked out." ::={ npNpiCardStatusEntry 8 } npNpiCseLlcWarningCode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the LLC stack has encountered an error condition which isn't serious enough to shut the peripheral down, but should be checked out." ::={ npNpiCardStatusEntry 9 } npNpiCseTcpWarningCode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the TCP stack has encountered an error condition which isn't serious enough to shut the peripheral down, but should be checked out." ::={ npNpiCardStatusEntry 10 } npNpiCseAtkWarningCode OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "This indicates that the AppleTalk stack has encountered an error condition which isn't serious enough to shut the peripheral down, but should be checked out." ::={ npNpiCardStatusEntry 11 } -- The Peripheral Attribute Entry npNpiPeripheralAttributeCount OBJECT-TYPE SYNTAX INTEGER (0..32) ACCESS read-only STATUS optional DESCRIPTION "The number of valid bytes of peripheral attributes received from the peripheral." ::={ npNpi 2 } npNpiPeripheralAttributeEntry OBJECT-TYPE SYNTAX NpNpiPeripheralAttributeEntry ACCESS not-accessible STATUS optional DESCRIPTION "The set of bytes that describe the peripheral's attributes as received from the peripheral during the setup of the peripheral to LAN card communications." INDEX { npNpiPaeLinkDirection } ::={ npNpi 3 } NpNpiPeripheralAttributeEntry ::= SEQUENCE { npNpiPaeLinkDirection INTEGER, npNpiPaeClass INTEGER, npNpiPaeIdentification INTEGER, npNpiPaeRevision INTEGER, npNpiPaeAppleTalk INTEGER, npNpiPaeMessage INTEGER, npNpiPaeReserved INTEGER, npNpiPaeMultichanFlag INTEGER, npNpiPaeDatagramFlag INTEGER } npNpiPaeLinkDirection OBJECT-TYPE SYNTAX INTEGER -- NO-PERIPH-DATA-XFER(0), -- XFER-PERIPH-TO-HOST(1), -- XFER-HOST-TO-PERIPH(2), -- BI-DIRECT-PERIPH-DATA-XFER(3) ACCESS read-only STATUS optional DESCRIPTION "The directions that the peripheral is able to transfer data (read and write channels, read channel only, or write channel only)." ::={ npNpiPeripheralAttributeEntry 1 } npNpiPaeClass OBJECT-TYPE SYNTAX INTEGER -- UNDEFINED-CLASS(0), -- PRINTER(1), -- PLOTTER(2), -- XStation(3) ACCESS read-only STATUS optional DESCRIPTION "The class assigned to the peripheral onto which this card is plugged." ::={ npNpiPeripheralAttributeEntry 2 } npNpiPaeIdentification OBJECT-TYPE SYNTAX INTEGER -- UNDEFINED-PERIPH(0), -- LASERJET-IIISI(1), -- LASERJET-4SI(5) ACCESS read-only STATUS optional DESCRIPTION "The Identification number of the peripheral. These values are defined in the MIO spec. DesignJet, PaintJet XL300, and DesignJet/600 peripherals will identify themselves as LaserJet-IIIsi." ::={ npNpiPeripheralAttributeEntry 3 } npNpiPaeRevision OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The revision number of the peripheral." ::={ npNpiPeripheralAttributeEntry 4 } npNpiPaeAppleTalk OBJECT-TYPE SYNTAX INTEGER -- NO-APPLETALK-SUPPORT(0), -- APPLETALK-SUPPORT(1) ACCESS read-only STATUS optional DESCRIPTION "Indicates the peripheral supports functionality that the apple talk protocol network provides." ::={ npNpiPeripheralAttributeEntry 5 } npNpiPaeMessage OBJECT-TYPE SYNTAX INTEGER -- NO-MSGMODE-SUPPORT(0), -- MSGMODE-SUPPORT(1) ACCESS read-only STATUS optional DESCRIPTION "Reserved for future use." ::={ npNpiPeripheralAttributeEntry 6 } npNpiPaeReserved OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This field is an unused byte." ::={ npNpiPeripheralAttributeEntry 7 } npNpiPaeMultichanFlag OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "An indication of how many MIO channels the peripheral supports." ::={ npNpiPeripheralAttributeEntry 8 } npNpiPaeDatagramFlag OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "An indication of how many MIO datagram channels the peripheral supports." ::={ npNpiPeripheralAttributeEntry 9 } -- The Card Attribute Entry npNpiCardAttributeEntry OBJECT-TYPE SYNTAX NpNpiCardAttributeEntry ACCESS not-accessible STATUS optional DESCRIPTION "The set of bytes describing the card's attributes as stored in the ROM of this particular LAN card." INDEX { npNpiPaeLinkDirection } ::={ npNpi 4 } NpNpiCardAttributeEntry ::= SEQUENCE { npNpiCaeLinkDirection INTEGER, npNpiCaeClass INTEGER, npNpiCaeIdentification INTEGER, npNpiCaeRevision INTEGER, npNpiCaeAppleTalk INTEGER, npNpiCaeMessage INTEGER, npNpiCaeReserved INTEGER, npNpiCaeMultichan INTEGER, npNpiCaeDatagram INTEGER } npNpiCaeLinkDirection OBJECT-TYPE SYNTAX INTEGER -- NO-LINK-DATA-XFER(0), -- XFER-LINK-TO-HOST(1), -- XFER-HOST-TO-LINK(2), -- BI-DIRECT-LINK-DATA-XFER(3) ACCESS read-only STATUS optional DESCRIPTION "The directions that this particular network peripheral card is able to transfer data (read and write, read only or write only)." ::={ npNpiCardAttributeEntry 1 } npNpiCaeClass OBJECT-TYPE SYNTAX INTEGER -- UNDEFINED-CLASS(0), -- RS-232(1), -- CENTRONICS(2), -- CSMA-CD-NETWORK(3), -- TOKEN-RING-NETWORK(4), -- SCSI(5), -- HPIB(6), -- LOCALTALK(7) ACCESS read-only STATUS optional DESCRIPTION "The class of this network peripheral card." ::={ npNpiCardAttributeEntry 2 } npNpiCaeIdentification OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS optional DESCRIPTION "The identification number assigned this network peripheral card." ::={ npNpiCardAttributeEntry 3 } npNpiCaeRevision OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The revision number of the network peripheral connection card code on this card." ::={ npNpiCardAttributeEntry 4 } npNpiCaeAppleTalk OBJECT-TYPE SYNTAX INTEGER -- NO-APPLETALK-SUPPORT(0), -- APPLETALK-SUPPORT(1) ACCESS read-only STATUS optional DESCRIPTION "Indicates that the card supports the apple talk protocol network." ::={ npNpiCardAttributeEntry 5 } npNpiCaeMessage OBJECT-TYPE SYNTAX INTEGER -- NO-MSGMODE-SUPPORT(0), -- MSGMODE-SUPPORT(1) ACCESS read-only STATUS optional DESCRIPTION "Indicates that the card supports the messaging mode protocol." ::={ npNpiCardAttributeEntry 6 } npNpiCaeReserved OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "Reserved object for future use." ::={ npNpiCardAttributeEntry 7 } npNpiCaeMultichan OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "An indication of how many MIO channels the I/O card supports." ::={ npNpiCardAttributeEntry 8 } npNpiCaeDatagram OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "An indication of how many MIO datagram channels the I/O card supports." ::={ npNpiCardAttributeEntry 9 } -- The Error Log Table subgroup of npCard npEltErrorLogTable OBJECT-TYPE SYNTAX SEQUENCE OF NpEltEntry ACCESS not-accessible STATUS optional DESCRIPTION "The LAN card's error log." ::={ npElt 1 } npEltEntry OBJECT-TYPE SYNTAX NpEltEntry ACCESS not-accessible STATUS optional DESCRIPTION "The LAN card's error log table entries." INDEX { npEltErrIndex } ::={ npEltErrorLogTable 1 } NpEltEntry ::= SEQUENCE { npEltErrIndex INTEGER, npEltErrErrorId INTEGER, npEltErrErrorParam INTEGER, npEltErrTimeStamp TimeTicks } npEltErrIndex OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The index that uniquely identifies an error log entry." ::={ npEltEntry 1 } npEltErrErrorId OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS optional DESCRIPTION "Identification for this error." ::={ npEltEntry 2 } npEltErrErrorParam OBJECT-TYPE SYNTAX INTEGER (0..4294967295) ACCESS read-only STATUS optional DESCRIPTION "Error Parameter value." ::={ npEltEntry 3 } npEltErrTimeStamp OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS optional DESCRIPTION "Time in timer ticks when error log entry was made." ::={ npEltEntry 4 } -- The IPX group npIpxGetUnitCfgResp OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "This object is the Get Unit Config Response structure described in the IPX code. This structure is of variable length depending on how many servers are configured." ::={ npIpx 1 } npIpx8022frametype OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of IPX FT8022 frames received." ::={ npIpx 2 } npIpxSNAPframetype OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of IPX FTSNAP frames received." ::={ npIpx 3 } npIpxEthernetframetype OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of IPX FTEthernet frames received." ::={ npIpx 4 } npIpx8023Rawframetype OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of IPX FT8023RAW frames received." ::={ npIpx 5 } npIpxSapInfo OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "This is a 50 byte array that contains the following information. 2 bytes: bindery object type (always 030c in hi-lo order) 12 bytes: Mac address of card (ASCII) 2 bytes: frame type also high bit (8000) is set if card is not configured 2 bytes : unit type (hex 81 for NetJet card) 32 bytes: node name (ASCII) which is: print server name for Queue Server mode printer name for RPTR mode" ::={ npIpx 6 } npIpxGetUnitCfgResp2 OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "This object is the Get Unit Config Response structure described in the IPX code. This structure is of variable length depending on how many servers are configured. This is the second set of info when more than 8 print servers are configured." ::={ npIpx 7 } -- Additions to the npIpx tree. -- These will not appear in the code until NDS is merged (not in EX+3). npIpxUnitName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..29)) ACCESS read-write STATUS optional DESCRIPTION "This is the name by which the device advertises over NetWare. In remote printer mode, this is referred to as the node name. In queue server mode this name doubles as the print server name used to log into a file server (in bindery mode). This value is settable. If a string that is longer than the maximum length is sent, the value will be truncated to the max. The max size does not include a null-terminating octet, nor does the string include a null octet. Setting this value to a zero length string or a single null character will cause the card to reset to factory defaults in the Novell mode only. Returning the node name to the NPIxxxxxx standard, resetting all options, and returning all slots to unconfigured. Any sets to this object will cause the card to reset, dropping all connections immediately (even in the middle of a job). This reset will occur even if the name sent is identical to the prior name." ::={ npIpx 8 } npIpxNdsTreeName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) ACCESS read-write STATUS optional DESCRIPTION "This is the name of the NDS tree by which the JetDirect attempts to connect and authenticate. NDS support is enabled when this value is provided (although connections do not become initiated until ipxUnitName is reset). To deconfigure the NDS support it is necessary to remove this tree name by setting the value to a zero length octet string or setting it to a single null character." ::={ npIpx 9 } npIpxNdsFullyQualifiedName OBJECT-TYPE SYNTAX NpIpxNdsFullyQualifiedName ACCESS not-accessible STATUS optional DESCRIPTION "These objects contain the NDS fully qualified print server name. If the npIpxNdsTreeName object is unconfigured, then this value is unused. The name is in length-preceded unicode format. The length is a four octet, little-endian integer. Following the length is a string of two octet unicode characters. The name is terminated by two zero octets. Example: CN=PS_Name.OU=boise.O=hp <50><0><0><0>C<0>N<0>=<0>P<0>S<0>_<0>N<0>a<0>m<0>e<0>.<0>O<0> U<0>=<0>b<0>o<0>i<0>s<0>e<0>.<0>O<0>=<0>h<0>p<0><0><0> Because the name can be very large, it is split up into two objects. The second object may be an empty string if the name is less than 128 characters long." INDEX { npIpxNdsFullyQualifiedName1 } ::={ npIpx 10 } NpIpxNdsFullyQualifiedName ::= SEQUENCE { npIpxNdsFullyQualifiedName1 OCTET STRING, npIpxNdsFullyQualifiedName2 OCTET STRING } npIpxNdsFullyQualifiedName1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6..260)) ACCESS read-write STATUS optional DESCRIPTION "The length and the first 128 characters of the NDS fully qualified print server name. " ::={ npIpxNdsFullyQualifiedName 1 } npIpxNdsFullyQualifiedName2 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..258)) ACCESS read-write STATUS optional DESCRIPTION "The rest of the NDS fully qualified print server name. This is the continuation of npIpxNdsFullyQualifiedName1 for names longer than 128 characters. The value will be an empty string if the name is less than 128 characters long." ::={ npIpxNdsFullyQualifiedName 2 } npIpxServerConnTable OBJECT-TYPE SYNTAX SEQUENCE OF NpIpxServerConnEntry ACCESS not-accessible STATUS optional DESCRIPTION "A list of npIpxServerConn entries." ::= { npIpx 11 } npIpxServerConnEntry OBJECT-TYPE SYNTAX NpIpxServerConnEntry ACCESS not-accessible STATUS optional DESCRIPTION "An entry contains the status of a file server connection. Each entry indicates the file server dynamically connected in the given slot, the connection status, NCP status, and NDS status. To set a new serverConnTable entry perform an snmpset of the serverConn name including only the column. The row will be returned. IpxUnitName {.1.3.6.1.4.1.11.2.4.3.10.8.0} is used to synchronize novell stack operation when multiple connTable entries are required. Normally, all connTable entries are first set, and then IpxUnitName is set. This triggers novell stack to reconfigure to use the the new connTable entries. New connTable entries are retrievable with get/getnext only after setting of the ipxUnixName. examples: To set connTable entry: $ snmpset -cinternal 15.29.43.73 .1.3.6.1.4.1.11.2.4.3.10.11.1.3 octetstring server1 .1.3.6.1.4.1.11.2.4.3.10.11.1.3.2 : OCTET STRING- (ascii): server1 $ snmpset -cinternal 15.29.43.73 .1.3.6.1.4.1.11.2.4.3.10.11.1.3 octetstring server2 .1.3.6.1.4.1.11.2.4.3.10.11.1.3.2 : OCTET STRING- (ascii): server2 To set ipxUnitName: $ snmpset -cinternal 15.29.43.73 .1.3.6.1.4.1.11.2.4.3.10.8.0 octetstring UNIT_A .1.3.6.1.4.1.11.2.4.3.10.8.0 : OCTET STRING- (ascii): UNIT_A To walk connTable: $ snmpwalk 15.29.43.73 .1.3.6.1.4.1.11.2.4.3.10.11 .1.3.6.1.4.1.11.2.4.3.10.11.1.1.1 : INTEGER: 1 .1.3.6.1.4.1.11.2.4.3.10.11.1.2.1 : INTEGER: 2 .1.3.6.1.4.1.11.2.4.3.10.11.1.3.1 : OCTET STRING- (ascii): server1 .1.3.6.1.4.1.11.2.4.3.10.11.1.4.1 : INTEGER: 4 .1.3.6.1.4.1.11.2.4.3.10.11.1.5.1 : INTEGER: 0 .1.3.6.1.4.1.11.2.4.3.10.11.1.6.1 : INTEGER: 0 .1.3.6.1.4.1.11.2.4.3.10.11.1.1.2 : INTEGER: 2 .1.3.6.1.4.1.11.2.4.3.10.11.1.2.2 : INTEGER: 2 .1.3.6.1.4.1.11.2.4.3.10.11.1.3.2 : OCTET STRING- (ascii): server2 .1.3.6.1.4.1.11.2.4.3.10.11.1.4.2 : INTEGER: 1 .1.3.6.1.4.1.11.2.4.3.10.11.1.5.2 : INTEGER: 0 .1.3.6.1.4.1.11.2.4.3.10.11.1.6.2 : INTEGER: 0 " INDEX { npIpxServerConnIndex } ::= { npIpxServerConnTable 1 } NpIpxServerConnEntry ::= SEQUENCE { npIpxServerConnIndex INTEGER, npIpxServerConnMode INTEGER, npIpxServerConnName OCTET STRING, npIpxServerConnStatus INTEGER, npIpxServerConnNcpStatus INTEGER, npIpxServerConnNdsStatus INTEGER } npIpxServerConnIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The index value which uniquely identifies the server connection to which this entry is applicable." ::= { npIpxServerConnEntry 1 } npIpxServerConnMode OBJECT-TYPE SYNTAX INTEGER { not-connected(1), qserver-bindery(2), rprinter(3), qserver-nds(4) } ACCESS read-only STATUS optional DESCRIPTION "The operating mode of the server." ::= { npIpxServerConnEntry 2 } npIpxServerConnName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..48)) ACCESS read-write STATUS optional DESCRIPTION "The name of the server." ::= { npIpxServerConnEntry 3 } npIpxServerConnStatus OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The RCFG connection status of the server." ::= { npIpxServerConnEntry 4 } npIpxServerConnNcpStatus OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The last NCP code of the server." ::= { npIpxServerConnEntry 5 } npIpxServerConnNdsStatus OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The last NDS code of the server." ::= { npIpxServerConnEntry 6 } npIpxObsoleteServerConnInfo OBJECT-TYPE SYNTAX NpIpxObsoleteServerConnInfo ACCESS not-accessible STATUS optional DESCRIPTION "These objects are obsolets, but are here for backwards compatility with pre-release software." INDEX { npIpxObsoleteServerConnInfo1 } ::={ npIpx 12 } NpIpxObsoleteServerConnInfo ::= SEQUENCE { npIpxObsoleteServerConnInfo1 OCTET STRING, npIpxObsoleteServerConnInfo2 OCTET STRING } npIpxObsoleteServerConnInfo1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(448)) ACCESS read-only STATUS optional DESCRIPTION "This object contains a list of 8 structures that refer to the status of the first eight file server connection slot entries. Each entry indicates the file server dynamically connected in the given slot. Besides the name of the file server, connection status, NCP status, and NDS status is provided. If the file server name in a given slot has '\0' in the first byte, that slot is not in use. The structure applied: struct { uchar opMode; // Operating mode of server // 0x00 = QServer (bindery) // 0x01 = RPrinter // 0x03 = QServer (nds) char fsName[48]; // name of file server in slot uchar connStat; // RCFG connection status uchar ncpStat; // last NCP code uchar pad; uint32 ndsStat; // last NDS code (big-endian) } slots[8];" ::={ npIpxObsoleteServerConnInfo 1 } npIpxObsoleteServerConnInfo2 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(448)) ACCESS read-only STATUS optional DESCRIPTION "The server connection info for slots 9-16. See above for format." ::={ npIpxObsoleteServerConnInfo 2 } -- The following is not an NDS related object (will be in EX+3) npIpxRcfgAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(12)) ACCESS read-write STATUS optional DESCRIPTION "The 12 octet IPX address of the Novell RCFG socket. The address is in network byte order." ::={ npIpx 13 } npIpxRcfgRemotePrintServerName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(12)) ACCESS read-write STATUS optional DESCRIPTION "Remote print server name. " ::={ npIpx 14 } npIpxRcfgRemotePrinterNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "remote Printer Number (valid in remote Printer Mode only) range: 0-255 for 4.X servers 0-15 for 3.X servers " ::={ npIpx 15 } npIpxRestart OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Setting of this object to zero causes a soft reset of the board, setting to one causes a hard reset of the board. " ::={ npIpx 16 } npIpxSourceRoute OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This object provides control/status for source route. Options for Token Ring networks are as follows: 00 - Auto Sensing mode 01 - Send without SR, receive only if same ring 02 - Send with SR, single route 03 - Send with SR, all routes used receive any " ::={ npIpx 17 } npIpxFrameType OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This object returns the frame type current enabled, possibilities are as follows: 00 - Auto 01 - Ethernet 8023 or Token-ring 02 - Ethernet II or Token-ring SNAP 03 - Ethernet 8022 04 - Ethernet SNAP" ::={ npIpx 18 } npIpxJobPollInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Queue server job poll interval." ::={ npIpx 19 } npIpxSapBroadcastInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Currently effective SAP broadcast Interval: range: 0-3600 seconds default: 60 seconds 0 value indicates SAP broadcasts are disabled. " ::={ npIpx 20 } npIpxPjlEnableFlag OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Currently effective PJL Enable Flag, possible values include: 00 - PJL disable 01 - PJL Job, banner 02 - Ustatus for end of job detection 03 - banners and end of job detection " ::={ npIpx 21 } npIpxTonerLowNotification OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Current Configuration for toner low notification. Possible values include: 00 - notify only if intervention is required. 01 - Notify even if peripheral is still operational. " ::={ npIpx 22 } --.1.3.6.1.4.1.11.2.4.3.5.10.0 npIpxNetNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "Current Ipx network number." ::={ npIpx 23 } -- Direct Mode Objects npDmConnSupp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This is the number of current active Direct Mode connections." ::={ npDm 1 } npDmConnAvail OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This is the number of Direct Mode connections available." ::={ npDm 2 } npDmProtSupp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This is a bit string that contains a list of protocols over which DirectMode is supported. A specified bit represents each protocol statck. Support for more than one stack is indicated by multiple bits ORed together. 0x01 = IPX/SPX 0x02 = TCP/IP 0x04 = DLC/LLC 0x08 = AppleTalk" ::={ npDm 3 } npDmServerInfo1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE(7..15)) ACCESS read-only STATUS optional DESCRIPTION "This object shows the address of the server that is connected to the DirectMode slot. This structure returns AT_AVAIL if there is no server attached to this slot and AT_NOSUPP if the slot number is out of range. struct{ ushort16 addrType; /* type of address */ ushort16 pktSize; /* size of negotiate packet size */ uchar8 addr[4-12]; /* address */ } AT_AVAIL 0 /* connection available */ AT_NOTSUPP 1 /* connection slot not supported */ AT_SPX 2 /* 12-byte SPX address */ AT_TCP 3 /* 4-byte TCP address */ AT_LLC 4 /* 6-byte LLC address */ AT_AT 5 /* Appletalk address */ Only AT_AVAIL, AT_NOTSUPP, and AT_SPX are currently supported." ::={ npDm 4 } -- LLC llcN2Value OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This is the value of the N2 variable used in the 802.2 type II connection. This value is the number of retransmissions that could occur if a host peer is not responding. The Ti timer is this value (N2) times 3 (N2 x 3). The value of the T1 timer is this value (N2) in seconds." ::={ llcconstategroup 1 } llcConnectionstate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This is the llc connection state for Lan Manager and Lan Server." ::={ llcconstategroup 7 } -- New LLC object npLlcServerAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-only STATUS optional DESCRIPTION "This is the LLC server address for Lan Manager and Lan Server." ::={ llcconstategroup 8 } -- This is a new sub-tree for port information. The first two apply to all -- JetDirect devices. The rest apply only to EX boxes. npPortNumPorts OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS optional DESCRIPTION "The number of peripheral interfaces supported by this device." ::={ npPort 1 } -- 1.3.6.1.4.1.11.2.4.3.13.2.0 npPortType OBJECT-TYPE SYNTAX INTEGER { unknown(1), mio(2), xio(3), parallel(4), centronics(5), bitronics(6), ecpNoMLC(7), serial(8), scsi(9), ecpMLC(10) } ACCESS read-only STATUS optional DESCRIPTION "The type of the peripheral interface. A parallel port will return the specific protocl currently in use. If the parallel port is disconnected it will return parallel(4)." ::={ npPort 2 } -- 1.3.6.1.4.1.11.2.4.3.13.3.0 npPortDesiredMode OBJECT-TYPE SYNTAX INTEGER { bitronics(1), -- compatibility forward, nibble-mode backchannel centronics(2), -- compatibility forward ecpWithMLC(3), -- Full bi-directional ECP w/ MLC ecpWithNibbleMLC(4), -- ECP forward, nibble-mode back-channel w/ MLC ecp(5) -- Full bi-directional ECP w/o MLC } ACCESS read-write STATUS optional DESCRIPTION "The desired (remotely specified) operating mode of the parallel port. The following map is used to determine mode availability and provides the definition for each mode: Available When npPortDesiredMode Definition ------------------ -------------- 1 bitronics always EX will attempt to retrieve nibble mode back channel data from the printer. If the printer does not support bitronics, EX will default back to compatibility mode. 2 centronics npPortMaxModeAvailable >= 1 EX will only support compatibility (centronics) mode when talking to the printer 3 ecpWithNibbleMLC npPortMaxModeAvailable >= 1 EX will attempt to talk to the printer across MLC. This is done by using ECP in the forward direction and nibble-mode bitronics in the reverse direction. If the printer does not support both MLC and ECP, EX will fall back to regular bitronics, as described above. 4 ecpWithMLC npPortMaxModeAvailable >= 1 EX will attempt to talk to the printer across MLC. This is done by using ECP in both forward and reverse directions. If the printer does not support both MLC and ECP, EX will fall back to regular bitronics, as described above. 5 ecp npPortMaxModeAvailable >= 1 EX will attempt to talk to the printer using ECP in both the forward and reverse directions. If the printer does not support ECP, EX will fall back to regular bitronics, as described above." ::={ npPort 3 } npPortCentronicsHandshaking OBJECT-TYPE SYNTAX INTEGER { nack-and-busy(1), nack-only(2), busy-only(3) } ACCESS read-write STATUS optional DESCRIPTION "The handshaking to be used in sending data over the parallel port." ::={ npPort 4 } npPortStatusLines OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The state of the centronics status lines from the peripheral. The value is a bit mask. Bit Value Signal 0 0x01 nACK 1 0x02 2 0x04 3 0x08 4 0x10 nFAULT 5 0x20 SELECT 6 0x40 PERROR 7 0x80 BUSY" ::={ npPort 5 } -- 1.3.6.1.4.1.11.2.4.3.13.6.0 npPortMaxModeAvaliable OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The maximum available parallel mode by which the print-server may connect to an attached peripheral. This is a function of the the available hardware and firmware capabilities. The value represents a mode of parallel operation, as defined in the following table: Value Mode ----- ----------------- 0x01 Centronics 0x03 ECP/MLC w/ nibble 0x04 ECP/MLC 0x05 ECP, No MLC" ::={ npPort 6 } -- 1.3.6.1.4.1.11.2.4.3.13.7.0 npPortBidiPollRate OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Poll rate for bi-directional data. Range is 10 to 100 seconds. Defaults to 40 seconds." ::={ npPort 7 } -- npXip xipActive OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION " This indicates whether the card and peripheral support XIP and at least one of the protocol stacks is enables (UDP or IPX)." ::= { npXip 1} -- CRC npCRCTable OBJECT-TYPE SYNTAX SEQUENCE OF NpCRCEntry ACCESS not-accessible STATUS optional DESCRIPTION "" ::= { npCRC 1 } npCRCEntry OBJECT-TYPE SYNTAX NpCRCEntry ACCESS not-accessible STATUS optional DESCRIPTION " " INDEX { npCRCIndex } ::= { npCRCTable 1 } NpCRCEntry ::= SEQUENCE { npCRCIndex INTEGER, npCRCText OCTET STRING, npCRCChannel INTEGER } npCRCIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { npCRCEntry 1 } npCRCText OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { npCRCEntry 2 } npCRCChannel OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "" ::= { npCRCEntry 3 } -- The DHCP group npDHCPconfig OBJECT-TYPE SYNTAX INTEGER { dhcpDisable(1), dhcpEnable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object allows a user to enable or disable configuration via DHCP. If DHCP is disabled, bootp is used for configuration. Supported in firmware revisions beginning with D-04-15, E-04-20(initial version, and ending at A,D,E-05." ::={ npDhcp 1 } -- 1.3.6.1.4.1.11.2.4.3.16.2.0 npDHCPserver OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "IP address of DHCP server that provided this unit with an IP address via the DHCP protocol." ::={ npDhcp 2 } --npScan group -- 1.3.6.1.4.1.11.2.4.3.17.1.0 npScanIdleTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The idle time, in seconds, after which an idle connection may be terminated. A value of zero disables the timeout." ::={ npScan 1 } -- 1.3.6.1.4.1.11.2.4.3.17.2.0 npScanTimeRemaining OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The time remaining, in seconds, until the current connection's lock expires. Once a connection's lock expires, JetDirect will terminate it if another connect request arrives. The time is reset whenever there is activity on the connection. A value of zero indicates there is no connection." ::={ npScan 2 } -- 1.3.6.1.4.1.11.2.4.3.17.3 npScanCurrentAddr OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "The remote address of the current scan connection. The format is a sockaddr structure containing an IP or IPX address." ::={ npScan 3 } -- 1.3.6.1.4.1.11.2.4.3.17.4.0 npScanCurrentName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "Human readable name of the current scan client. This object is a scratchpad for client software to provide the current user name so that other clients can include it in busy messages. JetDirect does not use this value; it is provided for cooperating software packages to notify each other of the current user name." ::={ npScan 4 } -- 1.3.6.1.4.1.11.2.4.3.17.5.0 npScanStatus OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "Current status of scanner. Status values TBD." ::={ npScan 5 } -- npWeb group -- .1.3.6.1.4.1.11.2.4.3.18.1.0 embeddedWebCfg OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "Functionality provided by embedded web server (ews). 0 = no ews 1 = ews on JetDirect for JetDirect status/configuration 4 = ews on JetDirect for scanner status/configuration 8 = ews on device for device status/configuration" ::={ npWeb 1 } -- .1.3.6.1.4.1.11.2.4.3.18.2.0 wjaFrameworkURL OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "Set by a present WJA system. Once set, the WJD user interface will add a framework link from the WJD navigation bar. This link will allow user navigation to the highest level page of WJA. This will allow users to easily navigate to WJA to manage other devices with the network. Since the URL can become stale, it is required that the WJD code verifies that the URL is active before actually using it. This is required since the WJA system may not always be operable. Maximum length of the url must be less than 255 bytes." ::={ npWeb 2 } -- .1.3.6.1.4.1.11.2.4.3.18.3.0 wjaFrameworkName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "Used by WJA systems as a scratch pad location for communication of current wja name. Name will be truncated to 64 characters." ::={ npWeb 3 } -- .1.3.6.1.4.1.11.2.4.3.18.4.0 extFrameworkURL OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "Set by a present external system. Once set, the WJD user interface will add a framework link from the WHD navigation bar. This link will allow user navigation to the highest level page of WJA. This will allow users to easily navigate to external systems to manage other devices with the network. Since the URL can become stale, it is required that the WJD code verifies that the URL is active before actually using it. This is required since the WJA system may not always be operable. Maximum length of the url must be less than 255 bytes." ::={ npWeb 4 } -- .1.3.6.1.4.1.11.2.4.3.18.5.0 extFrameworkName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "Used by external systems as a scratch pad location for communication of current wja name. Name will be truncated to 64 characters." ::={ npWeb 5 } -- .1.3.6.1.4.1.11.2.4.3.18.6.0 ippUrl OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION " Used by Internet Printing Protocol managers to define current URL. Maximum length of the url must be less than 255 bytes." ::={ npWeb 6 } -- Parallel port objects --- The Trap Group trapDestinationNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The number of trap destinations." ::={ trapDest 1 } ----------- The Trap Destination Table -------------- -- The code which processes the trap destination table -- utilizes a union to minimize data space. This is a very -- common "C" coding technique and adds important value. -- However, it introduces a complication to the design of this -- mib. The "C" union results in multiple definitions for the -- table entries, depending on protocol. There is no way (that -- I know of) to provide a compilable mib which shows multiple -- definitions for the objects. To resolve this I am showing the -- AF_IPX object definitions commented out. trapDestinationTable OBJECT-TYPE SYNTAX SEQUENCE OF TrapDestinationEntry ACCESS not-accessible STATUS optional DESCRIPTION "Protocol specific list of destinations to which the agent sends traps." ::= { trapDest 2 } trapDestinationEntry OBJECT-TYPE SYNTAX TrapDestinationEntry ACCESS not-accessible STATUS optional DESCRIPTION "Entries are a protocol specific sequence of trap destination parameters." INDEX { trapAddrFamily } ::= { trapDestinationTable 1 } TrapDestinationEntry ::= SEQUENCE { trapAddrFamily INTEGER, -- for ip trapAddrFamily trapAddrIp IpAddress, trapPort INTEGER, trapCommunityName OCTET STRING -- for ipx trapAddrFamily -- trapAddrNetwork -- INTEGER, -- trapAddrNode -- INTEGER, -- trapSocket, -- INTEGER, -- trapFrameType, -- INTEGER, -- trapPacketType, -- INTEGER, -- trapCommunityName, -- OCTET STRING, } -- for all protocols trapAddrFamily OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-write STATUS optional DESCRIPTION "Protocol family for trap. Possible values: 0 NOT_SET 1 AF_UDP 2 AF_IPX 3 AF_LLC 4 AF_DDP" ::= { trapDestinationEntry 1 } -- AF_UDP trapAddrIp OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS optional DESCRIPTION "Ip address of trap destination." ::= { trapDestinationEntry 2 } -- AF_UDP trapPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Host port to which traps are sent." ::= { trapDestinationEntry 3 } -- AF_UDP trapCommunityName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "Trap community name specified in the trap packet." ::= { trapDestinationEntry 4 } -- AF_IPX -- trapAddrNetwork OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "Network address of host to which traps are sent." -- ::= { trapDestinationEntry 2 } -- AF_IPX -- trapAddrNode OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "Node address of host to which traps are sent." -- ::= { trapDestinationEntry 3 } -- AF_IPX -- trapSocket OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "Host socket to which traps are sent." -- ::= { trapDestinationEntry 4 } -- AF_IP -- trapFrameType OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "Frame type for outbound packet" -- ::= { trapDestinationEntry 5 } -- AF_IPX -- trapPacketType OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "Packet type for outbound packet" -- ::= { trapDestinationEntry 6 } -- AF_IPX -- trapCommunityName OBJECT-TYPE -- SYNTAX OCTET STRING -- ACCESS read-write -- STATUS optional -- DESCRIPTION -- "Trap community name specified in the trap packet." -- ::= { trapDestinationEntry 7 } trapTest OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Causes agent to send an snmp trap to hosts registered in the trap destination table. Value specified will be used as the specific trap id." ::={ trapDest 3 } trapSource OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Sets the agent internal source for traps. Possibilities are as follows: 0 = ALL_TRAPS_ON 1 = ASYNC_PERIPHERAL_STATUS traps only 2 = proprietary pml traps only 3 = alert table traps only " ::={ trapDest 4 } -- Download Objects from ICF hpicfDownloadTable OBJECT-TYPE SYNTAX SEQUENCE OF HpicfDownloadEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of firmware downloads to this device. There will at any time be either 0 or 1 rows in this table, and the only valid index for this table is 1. It is only a table so that we may take advantage of the RowStatus textual convention for configuring the download parameters." ::= { hpicfDownload 1 } hpicfDownloadEntry OBJECT-TYPE SYNTAX HpicfDownloadEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The row in the hpicfDownloadTable containing the download parameters." INDEX { hpicfDownloadIndex } ::= { hpicfDownloadTable 1 } HpicfDownloadEntry ::= SEQUENCE { hpicfDownloadIndex INTEGER, hpicfDownloadOwnerAddress OCTET STRING, hpicfDownloadOwnerDomain OBJECT IDENTIFIER, hpicfDownloadTAddress OCTET STRING, hpicfDownloadTDomain OBJECT IDENTIFIER, hpicfDownloadFilename DisplayString, hpicfDownloadResetType INTEGER, hpicfDownloadErrorStatus INTEGER, hpicfDownloadErrorText DisplayString, -- hpicfDownloadStatus RowStatus hpicfDownloadStatus INTEGER } hpicfDownloadIndex OBJECT-TYPE SYNTAX INTEGER { dlInstance(1) } ACCESS not-accessible STATUS optional DESCRIPTION "The index which uniquely identifies this row. The only legal value for this object is 1." ::= { hpicfDownloadEntry 1 } hpicfDownloadOwnerAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "The transport address of the management station that initiated this download attempt, formatted according to the value of hpicfDownloadOwnerDomain. An attempt to modify this value will fail if the associated hpicfDownloadStatus object would be equal to 'active' both before and after the modification attempt." ::= { hpicfDownloadEntry 2 } hpicfDownloadOwnerDomain OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS optional DESCRIPTION "The kind of transport service used by the management station that initiated this download attempt. An attempt to modify this value will fail if the associated hpicfDownloadStatus object would be equal to 'active' both before and after the modification attempt." ::= { hpicfDownloadEntry 3 } hpicfDownloadTAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "The transport address of the node to download firmware from, formatted according to the value of hpicfDownloadTDomain. An attempt to modify this value will fail if the associated hpicfDownloadStatus object would be equal to 'active' both before and after the modification attempt." ::= { hpicfDownloadEntry 4 } hpicfDownloadTDomain OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-write STATUS optional DESCRIPTION "The kind of transport service to be used for the download. Currently supports snmpUDPDomain and snmpIPXDomain. An attempt to modify this value will fail if the associated hpicfDownloadStatus object would be equal to 'active' both before and after the modification attempt." ::= { hpicfDownloadEntry 5 } hpicfDownloadFilename OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS optional DESCRIPTION "Filename and path of file to download (maximum length of 63 characters + NULL). An attempt to modify this value will fail if the associated hpicfDownloadStatus object would be equal to 'active' both before and after the modification attempt." ::= { hpicfDownloadEntry 6 } hpicfDownloadResetType OBJECT-TYPE SYNTAX INTEGER { noReset(1), warmReset(2), factoryReset(3) } ACCESS read-write STATUS optional DESCRIPTION "The type of reset to perform after completion of the firmware download. Note that not all agents will support all possible values, and there may be other agent-specific values for this object." ::= { hpicfDownloadEntry 7 } hpicfDownloadErrorStatus OBJECT-TYPE SYNTAX INTEGER { fileNotFound(1), accessViolation(2), diskFull(3), illegalOperation(4), unknownTID(5), fileExists(6), noSuchUser(7), notDefined(8), corruptFile(9), noServer(10), tftpTimeout(11), hardwareError(12), success(13), inProgress(14), idle(15), erasing(16), incomplete(17) } ACCESS read-only STATUS optional DESCRIPTION "Status of download. The first seven codes are equal to the codes defined by the TFTP protocol. 'notDefined' is the same as TFTP protocol error 0. 'corruptFile' means that the agent detected a problem with the download file format. 'noServer' means the TFTP server at hpicfDownloadTAddress did not respond to the TFTP request. 'tftpTimeout' means that the download was aborted due to excessive timeouts. 'hardwareError' means that there was a hardware problem on the agent that forced an abort of the download (see hpicfDownloadErrorText for more detailed information). 'success' means that the download has completed successfully. 'inProgress' means that the TFTP transfer is currently active. 'idle means' that the download has not yet started (i.e. the value of hpicfDownloadStatus has not yet been set to 'active')." ::= { hpicfDownloadEntry 8 } hpicfDownloadErrorText OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS optional DESCRIPTION "A textual description of the current error status of the firmware download." ::= { hpicfDownloadEntry 9 } hpicfDownloadStatus OBJECT-TYPE -- SYNTAX RowStatus SYNTAX INTEGER { active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) } ACCESS read-write STATUS optional DESCRIPTION "The status of this download entry. This object may not be set to 'active' unless the following columnar objects exist in this row: hpicfDownloadOwnerAddress, hpicfDownloadOwnerDomain, hpicfDownloadTAddress, hpicfDownloadTDomain, and hpicfDownloadFilename." ::= { hpicfDownloadEntry 10 } hpicfDownloadLogMaxSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of the download log entries supported by this agent. Note that 0 is a legal value for this variable." ::= { hpicfDownload 2 } -- Access Control Objects setCommunityName OBJECT-TYPE SYNTAX OCTET-STRING ACCESS read-write STATUS optional DESCRIPTION "This object controls access of snmp read-write requests. Factory default configuration provides authentication of incoming packets with community names: internal and public. This object overrides the factory default settings so that the factory default setttings no longer work. This object returns SET or NOT_SET." ::= { community 1 } getCommunityName OBJECT-TYPE SYNTAX OCTET-STRING ACCESS read-only STATUS optional DESCRIPTION "This object controls access of snmp read requests. Factory default configuration provides authentication of incoming packets with community names: internal and public. This object provides access in addition to the factory default settings. This object returns SET or NOT_SET." ::= { community 2 } -- toptools group hpHttpMgDefaultURL OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-write STATUS optional DESCRIPTION "A Uniform Resource Locator (URL), as defined in RFC1738, for the default management information for this device. This URL is typically used by a HTTP browser to display management information for this device. This default page should contain links to any other management pages for this device." ::= { hpHttpMgDefaults 1} -- PML objects -- Generally, if PML is supported by the JD card and printer, PML object -- requests are repackaged by JetDirect from snmp format into "pml" -- and transmitted to the printer. Upon asynchronous return from the -- printer, the "pml" format data is repackaged back to snmp format -- and returned to the originator. If a pml object request is received -- by the JD card, and PML is not supported on that hardware combination -- then JD card returns a NONAME error. -- PML objects (.1.3.6.1.4.1.11.2.3.9.4.2...) are not defined by this mib. -- For definitions see appropriate printer mibs. -- The following PML objects are exceptions to the "general" passthru -- processing described above. For hardware combinations that support -- PML, these requests are passed thru as described above. For hardware -- that does not support PML, JD attempts to provide the data from another -- source (BIO, or Novell jobAccounting) rather than return the error -- specified above. Mib definitions for these objects are contained in -- the PML mib. These are repeated here for reference. They are commented -- out to avoid compile errors resulting from incomplete tree. -- 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.5.0 --totalEnginePageCount OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The total number of pages printed on the device as determined by -- PJL requests/responses. This value is normally a printer based -- MIB value. However, the JetDirect product can use PJL to determine -- an approximate page count in some situations. See the PML object -- definition (TOTAL-ENGINE-PAGE-COUNT) for more details." -- ::= { notYetStubbed 5 } -- 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.7.0 --totalColorPageCount OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The total number of color pages printed on the device as determined -- by PJL requests/responses. This value is normally a printer based -- MIB value. However, the JetDirect product can use PJL to determine -- an approximate page count in some situations. See the PML object -- definition (TOTAL-COLOR-PAGE-COUNT) for more details." -- ::= { notYetStubbed 7 } END